Octane with V6 and Octane Compression

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
User avatar
recondas
Moderator
Moderator
Posts: 5440
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Octane with V6 and Octane Compression

Unread postby recondas » Sat Jul 01, 2006 8:39 pm

Code: Select all

hinv -v -m
Location: /hw/node
      PM10360MHZ Board: barcode KYH395     part 030-1590-002 rev  B
Location: /hw/node/xtalk/15
            IP30 Board: barcode HXX639     part 030-1467-001 rev  B
Location: /hw/node/xtalk/15/pci/2
             FP1 Board: barcode 55598C     part 030-0891-003 rev  E
    PWR.SPPLY.ER Board: barcode AAE8250060 part 060-0035-001 rev  B
Location: /hw/node/xtalk/13
        XTALKPCI Board: barcode GRN860     part 030-0952-005 rev  C
Location: /hw/node/xtalk/11
           ODY32 Board: barcode KWC318     part 030-1403-003 rev  B
Location: /hw/node/xtalk/9
         COSMO20 Board: barcode LDV971     part 030-0933-003 rev  D
1 425 MHZ IP30 Processor
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 1536 Mbytes
Xbow ASIC: Revision 1.3
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
  CDROM: unit 4 on SCSI controller 1
  CDROM: unit 5 on SCSI controller 1
Integral SCSI controller 2: Version Fibre Channel QL2200A, 33 MHz PCI
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V6
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
  PCI Adapter ID (vendor 0x1077, device 0x2200) PCI slot 2
IMPACT Compression: unit 0, revision 0:1

Code: Select all

/usr/gfx/gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 1280x1024
        BUZZ version A.1
        PB&J version 1
        32MB memory
                Banks: 2, CAS latency: 3
         Monitor 0 type: Unknown
        Channel 0:
         Origin = (0,0)
         Video Output: 1280 pixels, 1024 lines, 96.04Hz (1280x1024_96)


With a V6 and a shoebox it looks like I get fastfan no matter where I stick the the Compression board :roll:

User avatar
QuicksilverG4
Posts: 771
Joined: Sun Nov 07, 2004 3:59 pm
Location: West of Philadelphia Pennsylvania, USA
Contact:

Unread postby QuicksilverG4 » Sun Jul 02, 2006 10:51 am

You got zafunks Compression didn't you? :)

I've got a cardcage a V6 and Compression in slot D and I don't get fastfans.

User avatar
recondas
Moderator
Moderator
Posts: 5440
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Unread postby recondas » Sun Jul 02, 2006 5:57 pm

QuicksilverG4 wrote:
I've got a cardcage a V6 and Compression in slot D and I don't get fastfans.


Thanks for the heads up - I've got it in C right now - I'll have to revisit D and see if I can get it to not run in fastfan.

Are you able to capture using jpeg compression?

User avatar
recondas
Moderator
Moderator
Posts: 5440
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Unread postby recondas » Tue Jul 04, 2006 5:01 pm

QuicksilverG4 wrote:I've got a cardcage a V6 and Compression in slot D and I don't get fastfans.


I moved the compression to slot D - back to normal fan speed.

Thanks QuicksilverG4 :wink:


Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 3 guests