Nekochan Net

Official Chat Channel: #nekochan // irc.nekochan.net
It is currently Wed May 22, 2013 1:24 pm

View unanswered posts | View active topics View unread posts


Board index » SGI » Getting Started, Documentation, Tips & Tricks

All times are UTC - 8 hours


Forum rules


Any posts concerning pirated software or offering to buy/sell/trade commercial software are subject to removal.



Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Print view Previous topic | First unread post | Next topic 
Author Message
diegel
 Post subject: l1cmd serial all
Unread postPosted: Thu Mar 29, 2012 2:29 am 
Offline

Joined: Tue Nov 17, 2009 2:08 am
Posts: 147
Location: Hamburg, Germany
I wonder how to update the serial information in L1. I added additional RAM to my Tezro, it is shown by hinv, but not by "l1cmd serial all". I entered update and enableall in PROM, but it still shows "no hardware detected" for the DIMMs with new RAM.

_________________
:Tezro: :Fuel: :Octane2: :Octane: :Onyx2: :O2+: :O2: :Indy: :Indigo: :Cube:
Top
 Profile  
 
hamei
 Post subject: Re: l1cmd serial all
Unread postPosted: Thu Mar 29, 2012 4:12 am 
Offline

Joined: Tue Feb 24, 2004 4:10 pm
Posts: 8345
Location: waist deep in the Big Muddy
diegel wrote:
I wonder how to update the serial information in L1. I added additional RAM to my Tezro, it is shown by hinv, but not by "l1cmd serial all". I entered update and enableall in PROM, but it still shows "no hardware detected" for the DIMMs with new RAM.

If you don't get a more intelligent suggestion, you could try moving them around so that the serial #'s in several slots were wrong. The only time I've had that problem was with mismatched memory pairs disabling some slots (the memory was not mismatched but the slot numbering was not what I thought) and an <enableall> fixed everything.
Top
 Profile  
 
recondas
 Post subject: Re: l1cmd serial all
Unread postPosted: Wed Apr 25, 2012 9:52 am 
Offline
Moderator
Moderator
User avatar

Joined: Sun Jun 06, 2004 4:55 pm
Posts: 4895
Location: NC - USA
diegel wrote:
I wonder how to update the serial information in L1. I added additional RAM to my Tezro, it is shown by hinv, but not by "l1cmd serial all". I entered update and enableall in PROM, but it still shows "no hardware detected" for the DIMMs with new RAM.


If you haven't already, try a reboot_l1, or better yet, completely remove power from the system/L1 (i.e., pull the plug). That will cause the L1 to re-inventory all the hardware that it queries via the I2C bus.

Sorry for the delayed response - somehow I missed your post on the first go-round.

_________________
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************
Top
 Profile  
 
diegel
 Post subject: Re: l1cmd serial all
Unread postPosted: Fri May 04, 2012 12:21 am 
Offline

Joined: Tue Nov 17, 2009 2:08 am
Posts: 147
Location: Hamburg, Germany
Thanks Recondas, 'l1cmd reboot_l1' works for me. I wasn't aware that the L1 is running even if the system is powered down.

_________________
:Tezro: :Fuel: :Octane2: :Octane: :Onyx2: :O2+: :O2: :Indy: :Indigo: :Cube:
Top
 Profile  
 
recondas
 Post subject: Re: l1cmd serial all
Unread postPosted: Fri May 04, 2012 7:11 am 
Offline
Moderator
Moderator
User avatar

Joined: Sun Jun 06, 2004 4:55 pm
Posts: 4895
Location: NC - USA
diegel wrote:
Thanks Recondas, 'l1cmd reboot_l1' works for me.
You're welcome, and again, thanks for the follow up.

_________________
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » SGI » Getting Started, Documentation, Tips & Tricks

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 0 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group