Nekochan Net

Official Chat Channel: #nekochan // irc.nekochan.net
It is currently Thu Oct 23, 2014 1:41 am

All times are UTC - 8 hours [ DST ]


Forum rules


Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.



Post new topic Reply to topic  [ 6 posts ] 
Author Message
Unread postPosted: Mon May 09, 2011 12:13 pm 
Offline

Joined: Mon Jul 26, 2010 9:13 am
Posts: 161
Got my new beastie up and running :)
There are a few tweaks to do yet, but here she as of right now:

hinv -vm:
Code:
Location: /hw/node
      PM10400MHZ Board: barcode KVT027     part 030-1475-001 rev  B
Location: /hw/node/xtalk/15
            IP30 Board: barcode LJR160     part 030-1467-001 rev  D
Location: /hw/node/xtalk/15/pci/2
    PWR.SPPLY.ER Board: barcode AAE1050280 part 060-0035-002 rev  A
             FP1 Board: barcode MCC629     part 030-0891-003 rev  H
Location: /hw/node/xtalk/11
  ODY128VERSIONB Board: barcode LKR459     part 030-1611-001 rev  C
1 400 MHZ IP30 Processor
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 1024 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3 serial port: tty1
IOC3 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 4265, device 3) pci slot 2
  PCI Adapter ID (vendor 4215, device 4128) pci slot 0
  PCI Adapter ID (vendor 4215, device 4128) pci slot 1
  PCI Adapter ID (vendor 4265, device 5) pci slot 3


/usr/gfx/gfxinfo output:
Code:
Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 1920x1200
        BUZZ version B.1
        PB&J version 1
        128MB memory
                Banks: 4, CAS latency: 3
        Channel 0:
         Origin = (0,0)
         Video Output: 1920 pixels, 1200 lines, 60.02Hz (1920x1200_60)


More to come later :)

_________________
:Octane2: Octane2 Dual R14K 600Mhz, 4GB RAM, VPro V12, DCD, PCI Card Cage, GBit Ethernet
:Indigo2IMP: Indigo2 R10K 195MHz, 1GB RAM, Maximum Impact, I2V
The boxen are breeding... help!


Last edited by Stoo on Fri Dec 02, 2011 11:36 am, edited 3 times in total.

Top
 Profile  
 
Unread postPosted: Wed May 11, 2011 10:42 am 
Offline

Joined: Mon Jul 26, 2010 9:13 am
Posts: 161
Soon to be 4GB ram :)

Card-cage installed now, just waiting for the drive sleds for the 2x 36 15k WorlDisk drives then I can upgrade the wee beasty to 6.5.30

I've bitten the bullet and ordered an external SCSI DVD rom too (fleabay to the rescue!)

Eventually I want to put a Dual 12K or even a Dual 14K in there if I can find one at the right price, as well as a gigabit card :)

_________________
:Octane2: Octane2 Dual R14K 600Mhz, 4GB RAM, VPro V12, DCD, PCI Card Cage, GBit Ethernet
:Indigo2IMP: Indigo2 R10K 195MHz, 1GB RAM, Maximum Impact, I2V
The boxen are breeding... help!


Top
 Profile  
 
Unread postPosted: Fri May 13, 2011 2:04 pm 
Offline

Joined: Mon Jul 26, 2010 9:13 am
Posts: 161
Getting there - LED lightbar mod completed - the bulbs had blown:

Image

The eagle-eyed may have spotted the external scsi dvd rom.. not operational yet - waiting for a cable & terminator :)

_________________
:Octane2: Octane2 Dual R14K 600Mhz, 4GB RAM, VPro V12, DCD, PCI Card Cage, GBit Ethernet
:Indigo2IMP: Indigo2 R10K 195MHz, 1GB RAM, Maximum Impact, I2V
The boxen are breeding... help!


Top
 Profile  
 
Unread postPosted: Fri Dec 02, 2011 11:33 am 
Offline

Joined: Mon Jul 26, 2010 9:13 am
Posts: 161
I've upgraded a little :D

Updated hinv:
Code:
-bash-4.0$ hinv -vm
Location: /hw/node
      PM20600MHZ Board: barcode MLD087     part 030-1778-001 rev  C
Location: /hw/node/xtalk/15
            IP30 Board: barcode KKP478     part 030-1467-001 rev  D
Location: /hw/node/xtalk/15/pci/2
    PWR.SPPLY.ER Board: barcode AAE1050280 part 060-0035-002 rev  A
             FP1 Board: barcode MCC629     part 030-0891-003 rev  H
Location: /hw/node/xtalk/13
        XTALKPCI Board: barcode HPD255     part 030-0952-005 rev  D
Location: /hw/node/xtalk/11
  ODY128VERSIONB Board: barcode LKR459     part 030-1611-001 rev  C
2 600 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R14000 Processor Chip Revision: 2.4
FPU: MIPS R14010 Floating Point Chip Revision: 0.0
Main memory size: 4096 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, pci 2
Gigabit Ethernet: eg0, PCI slot 1, firmware version 12.4.10
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
  PCI Adapter ID (vendor 0x10a9, device 0x0009) PCI slot 1
Dual Channel Display


/usr/gfx/gfxinfo output:
Code:
-bash-4.0$ /usr/gfx/gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 2560x1024
        BUZZ version B.1
        PB&J version 1
        128MB memory
                Banks: 4, CAS latency: 3
         Monitor 0 type: Unknown
        Dual Channel Display option
         Monitor 1 type: Unknown         Monitor 2 type: Unknown
        (Could not contact X server; thus, no XSGIvc information available)


DCD installed as well as a dual 600 R14000 :)

Oh, and a Gigabit ethernet card too :)

_________________
:Octane2: Octane2 Dual R14K 600Mhz, 4GB RAM, VPro V12, DCD, PCI Card Cage, GBit Ethernet
:Indigo2IMP: Indigo2 R10K 195MHz, 1GB RAM, Maximum Impact, I2V
The boxen are breeding... help!


Top
 Profile  
 
Unread postPosted: Fri Dec 02, 2011 12:13 pm 
Offline
User avatar

Joined: Fri Sep 25, 2009 10:40 am
Posts: 158
Location: Albany, OR USA
Cool! Looks like this Octane2 has been a fun project. 8-)

_________________
:Onyx2: 4x400MHz R12K Onyx2 IR2, 5GB RAM
:1600SW: :Indigo2IMP: R10K Indigo2 MaxIMPACT, 4 TRAMS, 768MB RAM, 2x9GB HD, CD-ROM, Phobos G160
Black Cardinal


Top
 Profile  
 
Unread postPosted: Sat Dec 03, 2011 4:03 am 
Offline

Joined: Mon Jul 26, 2010 9:13 am
Posts: 161
Yeah, it's been quite fun learning all the new things with all this SGI malarkey - I doubt the I2 is going to get much of a look in once I've gotten the install right :) (Still has the install it came with - really need to reinstall IRIX at some point - shouldn't be too bad - I still have the original disk (I cloned it as soon as I got hold of it) if anything goes wrong!

_________________
:Octane2: Octane2 Dual R14K 600Mhz, 4GB RAM, VPro V12, DCD, PCI Card Cage, GBit Ethernet
:Indigo2IMP: Indigo2 R10K 195MHz, 1GB RAM, Maximum Impact, I2V
The boxen are breeding... help!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group