Octane2, Dual R14k 600Mhz, 4GB, V12, DCD, PCI Card Cage, GBe

[Stoo]

Got my new beastie up and running
There are a few tweaks to do yet, but here she as of right now:

hinv -vm:

Code: Select all

Location: /hw/node
      PM10400MHZ Board: barcode KVT027     part 030-1475-001 rev  B
Location: /hw/node/xtalk/15
            IP30 Board: barcode LJR160     part 030-1467-001 rev  D
Location: /hw/node/xtalk/15/pci/2
    PWR.SPPLY.ER Board: barcode AAE1050280 part 060-0035-002 rev  A
             FP1 Board: barcode MCC629     part 030-0891-003 rev  H
Location: /hw/node/xtalk/11
  ODY128VERSIONB Board: barcode LKR459     part 030-1611-001 rev  C
1 400 MHZ IP30 Processor
Heart ASIC: Revision F
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 1024 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3 serial port: tty1
IOC3 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 4265, device 3) pci slot 2
  PCI Adapter ID (vendor 4215, device 4128) pci slot 0
  PCI Adapter ID (vendor 4215, device 4128) pci slot 1
  PCI Adapter ID (vendor 4265, device 5) pci slot 3


/usr/gfx/gfxinfo output:

Code: Select all

Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 1920x1200
        BUZZ version B.1
        PB&J version 1
        128MB memory
                Banks: 4, CAS latency: 3
        Channel 0:
         Origin = (0,0)
         Video Output: 1920 pixels, 1200 lines, 60.02Hz (1920x1200_60)


More to come later

[Stoo]

Soon to be 4GB ram

Card-cage installed now, just waiting for the drive sleds for the 2x 36 15k WorlDisk drives then I can upgrade the wee beasty to 6.5.30

I've bitten the bullet and ordered an external SCSI DVD rom too (fleabay to the rescue!)

Eventually I want to put a Dual 12K or even a Dual 14K in there if I can find one at the right price, as well as a gigabit card

[Stoo]

Getting there - LED lightbar mod completed - the bulbs had blown:



The eagle-eyed may have spotted the external scsi dvd rom.. not operational yet - waiting for a cable & terminator

[Stoo]

I've upgraded a little

Updated hinv:

Code: Select all

-bash-4.0$ hinv -vm
Location: /hw/node
      PM20600MHZ Board: barcode MLD087     part 030-1778-001 rev  C
Location: /hw/node/xtalk/15
            IP30 Board: barcode KKP478     part 030-1467-001 rev  D
Location: /hw/node/xtalk/15/pci/2
    PWR.SPPLY.ER Board: barcode AAE1050280 part 060-0035-002 rev  A
             FP1 Board: barcode MCC629     part 030-0891-003 rev  H
Location: /hw/node/xtalk/13
        XTALKPCI Board: barcode HPD255     part 030-0952-005 rev  D
Location: /hw/node/xtalk/11
  ODY128VERSIONB Board: barcode LKR459     part 030-1611-001 rev  C
2 600 MHZ IP30 Processors
Heart ASIC: Revision F
CPU: MIPS R14000 Processor Chip Revision: 2.4
FPU: MIPS R14010 Floating Point Chip Revision: 0.0
Main memory size: 4096 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, pci 2
Gigabit Ethernet: eg0, PCI slot 1, firmware version 12.4.10
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
  PCI Adapter ID (vendor 0x10a9, device 0x0009) PCI slot 1
Dual Channel Display


/usr/gfx/gfxinfo output:

Code: Select all

-bash-4.0$ /usr/gfx/gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 2560x1024
        BUZZ version B.1
        PB&J version 1
        128MB memory
                Banks: 4, CAS latency: 3
         Monitor 0 type: Unknown
        Dual Channel Display option
         Monitor 1 type: Unknown         Monitor 2 type: Unknown
        (Could not contact X server; thus, no XSGIvc information available)


DCD installed as well as a dual 600 R14000

Oh, and a Gigabit ethernet card too

[Black Cardinal]

Cool! Looks like this Octane2 has been a fun project.

[Stoo]

Yeah, it's been quite fun learning all the new things with all this SGI malarkey - I doubt the I2 is going to get much of a look in once I've gotten the install right (Still has the install it came with - really need to reinstall IRIX at some point - shouldn't be too bad - I still have the original disk (I cloned it as soon as I got hold of it) if anything goes wrong!