Attachment:
Fuel-n-F180.jpg [ 120.51 KiB | Viewed 394 times ]
For sale - 600MHz Fuel workstation. It is currently set up with 2GB of memory, a V10 graphics, a DM6 SD video capture board, an m-Audio Revolution 7.1/DM8 audio board, an SGI PCI gigabit ethernet board (copper), and a clone DM10 firewire board. I replaced the original CD-ROM with a Plextor CD-RW drive that works equally well as a install drive or a CD burner. The skins are in nice but not perfect condition, and the latching tab is intact on the drive door. It has a platform appropriate operating system and a few extras installed - PM me for details.
Code:
hinv -vm
Location: /hw/module/001c01/node
IP34 Board: barcode MMN520 part 030-1707-003 rev -H
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode MRS271 part 030-1730-001 rev -G
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODY10 Board: barcode MVT940 part 030-1826-003 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode MMN520 part 030-1707-003 rev -H
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode MMN520 part 030-1707-003 rev -H
1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.3
FPU: MIPS R14010 Floating Point Chip Revision: 2.3
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 4 MB Speed 300 Mhz Tap 0xa
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 2048 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 2: Version IEEE1394 SBP2
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 5 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V10
Gigabit Ethernet: eg0, module 001c01, pci_bus 2, pci_slot 2, firmware version 0.0.0
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version MAD revision 1, number 2
PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0009) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x10ee, device 0xd151) PCI slot 2
PCI Adapter ID (vendor 0x104c, device 0x8020) PCI slot 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
SD-DIGVID Standard Definition Digital Video: unit 0, revision 2.75.0
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
Code:
# /usr/gfx/gfxinfo -v
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1280x1024
BUZZ version B.2
PB&J version 1
32MB memory
Banks: 2, CAS latency: 3
Monitor 0 type: Unknown
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)
I'm asking $300 for the system, $400 with the SGI F180 LCD Display shown in the photo. If you're on a tight budget I'd sell just the Fuel with 512MB of RAM and no PCI option boards for $175. I'm located in North Carolina. Pick up in person and I'm sure we can find something to make the drive worth your while.
UPDATE: The Fuel has been sold. Thank you for your interest.
Login
Register
FAQ
Search
