Nekochan Net

Official Chat Channel: #nekochan // irc.nekochan.net
It is currently Tue May 21, 2013 1:06 pm

View unanswered posts | View active topics View unread posts


Board index » SGI » SGI: Hardware

All times are UTC - 8 hours


Forum rules


Any posts concerning pirated software or offering to buy/sell/trade commercial software are subject to removal.



Post new topic Reply to topic  Page 1 of 1
  [ 2 posts ] 
  Print view Previous topic | First unread post | Next topic 
Author Message
kubatyszko
 Post subject: Fuel not starting
Unread postPosted: Fri May 04, 2012 5:10 am 
Offline

Joined: Sat Nov 12, 2011 3:18 am
Posts: 296
Location: Tokyo
Hi there, I'm trying to bring my other Fuel (in Poland) back to life, I got an ATX PSU installed (using my famous adapters),
I am able to get into L1, check everything and issue power up:

Code:
001a01-L1>?

SGI SN1 L1 Controller
Firmware Image B: Rev. 1.20.6, Built 03/12/2003 11:01:29


001a01-L1>
001a01-L1>env
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
           12V   Wait Pwr  10%  10.80/ 13.20  20%   9.60/ 14.40    0.00
        12V IO   Wait Pwr  10%  10.80/ 13.20  20%   9.60/ 14.40    0.00
            5V   Wait Pwr  10%   4.50/  5.50  20%   4.00/  6.00    0.00
          3.3V   Wait Pwr  10%   2.97/  3.63  20%   2.64/  3.96    0.26
          2.5V   Wait Pwr  10%   2.25/  2.75  20%   2.00/  3.00    0.00
          1.5V   Wait Pwr  10%   1.35/  1.65  20%   1.20/  1.80    0.00
        5V aux   Wait Pwr  10%   4.50/  5.50  20%   4.00/  6.00    5.10
      3.3V aux   Wait Pwr  10%   2.97/  3.63  20%   2.64/  3.96    3.29
PIMM0 12V bias   Wait Pwr  10%  10.80/ 13.20  20%   9.60/ 14.40    0.00
     Fuel SRAM   Wait Pwr  10%   2.25/  2.75  20%   2.00/  3.00    0.03
      Fuel CPU   Wait Pwr  10%   1.44/  1.76  20%   1.28/  1.92    0.01
    PIMM0 1.5V   Wait Pwr  10%   1.35/  1.65  20%   1.20/  1.80    0.01
PIMM0 3.3V aux   Wait Pwr  10%   2.97/  3.63  20%   2.64/  3.96    3.29
  PIMM0 5V aux   Wait Pwr  10%   4.50/  5.50  20%   4.00/  6.00    5.12
  XIO 12V bias   Wait Pwr  10%  10.80/ 13.20  20%   9.60/ 14.40    0.00
        XIO 5V   Wait Pwr  10%   4.50/  5.50  20%   4.00/  6.00    0.00
      XIO 2.5V   Wait Pwr  10%   2.25/  2.75  20%   2.00/  3.00    0.00
  XIO 3.3V aux   Wait Pwr  10%   2.97/  3.63  20%   2.64/  3.96    3.30

Description    State       Warning RPM  Current RPM
-------------- ----------  -----------  -----------
FAN 0  EXHAUST   Wait Pwr          920            0
FAN 1       HD   Wait Pwr         1560            0
FAN 2      PCI   Wait Pwr         1120            0
FAN 3    XIO 1   Wait Pwr         1600            0
FAN 4    XIO 2   Wait Pwr         1600            0
FAN 5       PS   Wait Pwr         1600            0

                           Advisory   Critical   Fault      Current
Description    State       Temp       Temp       Temp       Temp   
-------------- ----------  ---------  ---------  ---------  ---------
NODE 0           Wait Pwr   60C/140F   65C/149F   70C/158F   22C/ 71F
NODE 1           Wait Pwr   60C/140F   65C/149F   70C/158F   23C/ 73F
NODE 2           Wait Pwr   60C/140F   65C/149F   70C/158F   23C/ 73F
PIMM             Wait Pwr   60C/140F   65C/149F   70C/158F   22C/ 71F
ODYSSEY          Wait Pwr   60C/140F   65C/149F   70C/158F   23C/ 73F
BEDROCK          Wait Pwr  Not currently available

001a01-L1>power up
001a01-L1>env
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
           12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.88
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00
            5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.17
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.34
          2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.46
          1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.47
        5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.07
      3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.29
PIMM0 12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
     Fuel SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.54
      Fuel CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.59
    PIMM0 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
PIMM0 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.29
  PIMM0 5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.10
  XIO 12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.94
        XIO 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.17
      XIO 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.47
  XIO 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.30

Description    State       Warning RPM  Current RPM
-------------- ----------  -----------  -----------
FAN 0  EXHAUST    Enabled          920         1219
FAN 1       HD    Enabled         1560         2229
FAN 2      PCI    Enabled         1120         1558
FAN 3    XIO 1    Enabled         1600         2274
FAN 4    XIO 2    Enabled         1600         2103
FAN 5       PS    Enabled         1600         1781

                           Advisory   Critical   Fault      Current
Description    State       Temp       Temp       Temp       Temp   
-------------- ----------  ---------  ---------  ---------  ---------
NODE 0            Enabled   60C/140F   65C/149F   70C/158F   22C/ 71F
NODE 1            Enabled   60C/140F   65C/149F   70C/158F   23C/ 73F
NODE 2            Enabled   60C/140F   65C/149F   70C/158F   23C/ 73F
PIMM              Enabled   60C/140F   65C/149F   70C/158F   22C/ 71F
ODYSSEY           Enabled   60C/140F   65C/149F   70C/158F   23C/ 73F
BEDROCK           Enabled   70C/158F   75C/167F   80C/176F   21C/ 69F

001a01-L1>
001a01-L1>serial all

Data                            Location      Value
------------------------------  ------------  --------
Local System Serial Number      EEPROM        08:00:69:21:99:12
Local Brick Serial Number       EEPROM        MYD069
Reference Brick Serial Number   NVRAM         MYD069


EEPROM      Product Name    Serial      Part Number           Rev  T/W   
----------  --------------  ----------  --------------------  ---  ------
NODE        IP34            MYD069      030_1707_003          L    00   
MAC         MAC ADDRESS     NA          NA                    NA   NA   
PIMM        IP34PIMM        MKZ626      030_1730_001          G    00   
XIO         ASTODYV10       MXH355      030_1826_002          A    00   

EEPROM     JEDEC-SPD Info           Part Number        Rev Speed  SGI
---------- ------------------------ ------------------ --- ------ --------
DIMM 0     CE000000000000000CFE7000 M3 46L3313DT2-CA0  2D   10.0  N/A
DIMM 2     CE000000000000000C5BAD02 M3 46L3313DT2-CA0  2D   10.0  N/A
DIMM 1     CE000000000000000CFF7000 M3 46L3313DT2-CA0  2D   10.0  N/A
DIMM 3     CE000000000000000C65AD02 M3 46L3313DT2-CA0  2D   10.0  N/A

001a01-L1>



But all I get upon startup in console is:

Code:
Connected


IP35 PROM SGI Version 6.210  built 02:33:51 PM Aug 26, 2004
Running in DDR mode
Testing/Initializing memory ...............      DONE
Copying PROM code to memory ...............      DONE
Discovering local IO ......................      


I waited a couple minutes after the last message with no luck, looking at my primary fuel, there should be either message about widget not present (Vpro) or NUMA following.

I'm pretty sure some 5 months ago this Fuel worked, I might have swapped the PIMM (for another with the same frequency - also working) and/or memory, but even if something was wrong it should at least go beyond that message in the console...

Any thoughts ?

Thanks

_________________
[click for links to hinv] JP: [ :O200: :Fuel: :Octane2: :Octane: :O2: :Indy: :Indy: ] PL: [ :Fuel: :O2: :O2+: :Indy: ]
For Sale: 2*O200 M/B, 2*O200 PSU, 6*256MB O200 RAM, 2*O200 SCSI Backplane, 2*O200 MSC, DMediaPro DM-2 ( 030-1653-002 Rev. H , XT-DIGVID) with Octane XIO pull (Origin pull optionally available)
Top
 Profile  
 
hamei
 Post subject: Re: Fuel not starting
Unread postPosted: Fri May 04, 2012 11:36 pm 
Offline

Joined: Tue Feb 24, 2004 4:10 pm
Posts: 8341
Location: waist deep in the Big Muddy
kubatyszko wrote:
Any thoughts ?

If you're doing this over the console you probably don't have the graphics readout ? Is it still at the red light or do you get to flashing white ?

The thing that I always check first is the scsi cable to the disks. SGI must have saved thirty cents on that thing, it seems to be very brittle and flaky.

I had this same thing happen when a graphics board went bad, hope that is not your problem but you can check by sticking a known-good board in there if you have one handy. Memory is also a possibility - when I accidentally installed the memory in not-pairs once the computer was quite unhappy. Disabled both memory banks, in fact. That was something of a problem :)

Fuels are not as touchy as O2s but in my experience they don't like to be moved around and parts swapped very much. Double check cables, connections, screws, all that stuff. Did you upgrade the pimm by any chance ? They won't boot with a slower pimm installed than what they think it should be.

edit: oops. I see your memory shows up fine. Okay, scratch that possible cause.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 2 posts ] 

Board index » SGI » SGI: Hardware

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group