Origin2000: 8x 250MHz, 5GB RAM

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
User avatar
Dodoid
Posts: 736
Joined: Mon Jul 04, 2016 1:36 pm
Location: Ottawa, Canada
Contact:

Origin2000: 8x 250MHz, 5GB RAM

Unread postby Dodoid » Wed Jan 31, 2018 9:04 pm

Running the Origin2000 today (just set up an Xvnc server, hope to have an IO6G so that the SI graphics I installed work soon). I should be able to get a video on my channel about this system out soon-ish, though it does require some strange special considerations given that I can't film it on my normal white background.

Hinv below, but the "simple" specs are as follows:
  • 8x 250MHz CPUs across 4 nodeboards
  • 5GB memory
  • SI graphics (installed, appears in PROM hinv, seemingly not used by IRIX yet)
  • 18GB disk
  • Both nodeboards standard routers
  • IRIX 6.5.30

Pics below, hope these are better resolution than the whopping 300x294 image I had to use for my SGI History series (before I owned an Origin2000 of my own) :D . Skins are in good condition, thanks to PixelDust1 who I bought this system from. Same goes for my Onyx, hope I can get that running soon.

2018-01-31 23.46.34.jpg
Front. Nice skins. The system lives under my desk, which is exactly where it is pictured here. I have cables for ethernet, serial, etc running out the back, connected to my Hackintosh workstation and my network so that I can run it remotely just by turning the key. I can even use it as a footwarmer if I want to.

2018-01-31 23.46.50.jpg
Front slidey-panel-thing down. As you can see, I only have one hard drive in it (my SGI "server" is actually an 400mhz O2, for power consumption and noise reasons). That CD-ROM is the same model used in the O2, seen here with the factory faceplate (as opposed to the three-piece blue and black replacement design used on the O2. It required the same eject gear repair, but now works great.

2018-01-31 23.48.55.jpg
I pulled the system out to get some pics. It's on wheels of course, so I've positioned it so that I can just roll it in and out from under the desk. The cables remain attached and the system remains running, since I use long cables with enough slack to move the system out if I need to.

2018-01-31 23.49.08.jpg
SI graphics card. I stole the bracket thing off a SCSI card it had in there that I didn't need, card came from the parts bin. I have just stuck the tab out the side for now, rather than cutting a new hole. Works well enough, holds the card in, shows up in PROM hinv. The blank card next to it loses about a milimeter of space, so I just bent it's back plate in a tiny amount to get it to fit beside the slightly wider SI card.

hinv -vm

Code: Select all

Location: /hw/module/1/slot/n1/node
        MODULEID Board: barcode K0019523   part              rev   
       8P12_MPLN Board: barcode HJG486     part 030-0762-006 rev  M
            IP31 Board: barcode JEA753     part 030-1255-003 rev  D
        IP31PIMM Board: barcode FXZ207     part 030-1313-002 rev  A
Location: /hw/module/1/slot/n2/node
            IP31 Board: barcode DDP546     part 030-1255-003 rev  A
        IP31PIMM Board: barcode GFE410     part 030-1313-002 rev  A
Location: /hw/module/1/slot/n3/node
        IP31PIMM Board: barcode GFJ969     part 030-1313-002 rev  A
            IP31 Board: barcode FXN470     part 030-1255-003 rev  A
Location: /hw/module/1/slot/n4/node
            IP31 Board: barcode DGK911     part 030-1255-003 rev  B
        IP31PIMM Board: barcode GBY993     part 030-1313-002 rev  A
Location: /hw/module/1/slot/r1/router
      ROUTER_IR1 Board: barcode KCF653     part 030-0841-003 rev  B
Location: /hw/module/1/slot/r2/router
      ROUTER_IR1 Board: barcode KDK186     part 030-0841-003 rev  B
Location: /hw/module/1/slot/io11/xtalk_pci
       XTALK_PCI Board: barcode LHY742     part 030-1275-003 rev  A
Location: /hw/module/1/slot/io1/baseio
          BASEIO Board: barcode EPB029     part 030-1124-002 rev  B
8 250 MHZ IP27 Processors
CPU: MIPS R10000 Processor Chip Revision: 3.4
FPU: MIPS R10010 Floating Point Chip Revision: 3.4
CPU 0 at Module 1/Slot 1/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 1 at Module 1/Slot 1/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 2 at Module 1/Slot 2/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 3 at Module 1/Slot 2/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 4 at Module 1/Slot 3/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 5 at Module 1/Slot 3/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 6 at Module 1/Slot 4/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 7 at Module 1/Slot 4/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
Main memory size: 5120 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 1/Slot 1: 896 MB (enabled)
  Bank 0 contains 128 MB (Standard) DIMMS (enabled)
  Bank 1 contains 128 MB (Standard) DIMMS (enabled)
  Bank 2 contains 128 MB (Standard) DIMMS (enabled)
  Bank 3 contains 128 MB (Standard) DIMMS (enabled)
  Bank 4 contains 128 MB (Standard) DIMMS (enabled)
  Bank 5 contains 128 MB (Standard) DIMMS (enabled)
  Bank 6 contains 128 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 2: 640 MB (enabled)
  Bank 0 contains 128 MB (Standard) DIMMS (enabled)
  Bank 1 contains 128 MB (Standard) DIMMS (enabled)
  Bank 2 contains 128 MB (Standard) DIMMS (enabled)
  Bank 3 contains 128 MB (Standard) DIMMS (enabled)
  Bank 4 contains 128 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 3: 256 MB (enabled)
  Bank 0 contains 256 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 4: 3328 MB (enabled)
  Bank 0 contains 256 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
  Bank 2 contains 512 MB (Standard) DIMMS (enabled)
  Bank 3 contains 512 MB (Standard) DIMMS (enabled)
  Bank 4 contains 512 MB (Standard) DIMMS (enabled)
  Bank 5 contains 512 MB (Standard) DIMMS (enabled)
  Bank 6 contains 512 MB (Standard) DIMMS (enabled)
ROUTER in Module 1/Slot 2: Revision 2: Active Ports [4,5,6] (enabled)
ROUTER in Module 1/Slot 4: Revision 2: Active Ports [4,5,6] (enabled)
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
Origin BASEIO board, module 1 slot 1: Revision 3
  PCI Adapter ID (vendor 0x10b7, device 0x5900) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 1: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 2: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 3: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 4: Revision 5 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n1: Revision 6.156
IP27prom in Module 1/Slot n2: Revision 6.156
IP27prom in Module 1/Slot n3: Revision 6.156
IP27prom in Module 1/Slot n4: Revision 6.156
IO6prom on Global Master Baseio in Module 1/Slot io1: Revision 6.156


Like I said, hope to get more out about this system soon. I have been slowly cleaning up my bedroom (where my larger systems are located), so I should be able to film in there.
Last edited by Dodoid on Thu Feb 01, 2018 3:22 pm, edited 1 time in total.
:Onyx: :O2000: :Fuel: :Octane: :Octane: :Octane: :O2: :O2: :Indigo2: :Indigo2: :Indy: :Indy:
and a small army of Image

User avatar
josehill
Moderator
Moderator
Posts: 3396
Joined: Mon Jun 06, 2005 9:53 pm
Location: New England, USA
Contact:

Re: Origin2000: 8x 250MHz, 5GB RAM

Unread postby josehill » Thu Feb 01, 2018 6:58 am

Very nice system!

User avatar
VenomousPinecone
Posts: 2180
Joined: Mon Jun 20, 2005 2:10 pm
Location: Groom Lake, NV

Re: Origin2000: 8x 250MHz, 5GB RAM

Unread postby VenomousPinecone » Thu Feb 01, 2018 9:12 am

Man I love it. Always wanted my own deskside system, it seemed like the coolest compromise between big iron and a workstation. Now all you need are some moody low light pics to show of all the blinkenlights in true glory.


Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 2 guests