Onyx 4/G2N - 4x1GHz/4x700MHz with G2N/Voyager/ATI Graphics

[jwhat]

Hi Nekochaners,

I have continued to try various combinations of Onyx 4 chassis’s with V12 & SG2 graphics.

To test that the Onyx 4/G2 (ATI Graphics with no CPUs) is pretty much a standard Chimera, I put a 4x700MHz CPU Processor board from deskside Tezro into the CPU-less G2 chassis. As the G2 has no IO9 board I then numalink'ed it to second 4x1GHz Onyx 4.

To get this up and running I had to do clean IRIX install, as I could not get existing IP35/V12 Graphics boot disk to upgrade to SG2 graphics.

This setup works. So I have have: [Onyx 4/Onyx 4 with V12] combo and [Onyx 4/Onyx 4 with SG2 (Voyager/ATI] combination.

By adding of 4x700MHz CPU board to G2, that makes it an G2N node now (as per "SGI Onyx Next Generation Scalable Graphics Platform User’s Guide" documentation: http://irix7.com/techpubs/007-4634-001.pdf).

Here is hinv / uname / gfxinfo:

Code: Select all

# hinv -mv
Location: /hw/module/001c02/node
       IP59_4CPU Board: barcode RMB786     part 030-1989-003 rev -D
Location: /hw/module/001c02/IXbrick/xtalk/15
       2U_INT_53 Board: barcode NCA858     part 030-1809-003 rev -B
Location: /hw/module/001c02/IXbrick/xtalk/15/pci-x/0/1/ioc4
             IO9 Board: barcode RAD764     part 030-1771-006 rev -A
Location: /hw/module/001c03/node
       IP53_4CPU Board: barcode NET662     part 030-1868-001 rev -C
Location: /hw/module/001c03/CGbrick/xtalk/15
       2U_INT_53 Board: barcode NLA195     part 030-1809-006 rev -B
Processor 0: 1.0 GHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 3.0
FPU: MIPS R16010 Floating Point Chip Revision: 3.0
Processor 1: 1.0 GHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 3.0
FPU: MIPS R16010 Floating Point Chip Revision: 3.0
Processor 2: 1.0 GHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 3.0
FPU: MIPS R16010 Floating Point Chip Revision: 3.0
Processor 3: 1.0 GHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 3.0
FPU: MIPS R16010 Floating Point Chip Revision: 3.0
Processor 4: 700 MHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
Processor 5: 700 MHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
Processor 6: 700 MHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
Processor 7: 700 MHZ IP35
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
CPU 0 at Module 001c02/Slot 0/Slice A: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 1 at Module 001c02/Slot 0/Slice B: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 2 at Module 001c02/Slot 0/Slice C: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 3 at Module 001c02/Slot 0/Slice D: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 4 at Module 001c03/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 5 at Module 001c03/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 6 at Module 001c03/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 7 at Module 001c03/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
Main memory size: 8192 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 16 Mbytes
Secondary unified instruction/data cache size: 16 Mbytes
Secondary unified instruction/data cache size: 16 Mbytes
Secondary unified instruction/data cache size: 16 Mbytes
Secondary unified instruction/data cache size: 4 Mbytes
Secondary unified instruction/data cache size: 4 Mbytes
Secondary unified instruction/data cache size: 4 Mbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c02/Slot 0: 4096 MB (enabled)
  Bank 0 contains 512 MB (Premium) DIMMS (enabled)
  Bank 1 contains 512 MB (Premium) DIMMS (enabled)
  Bank 2 contains 512 MB (Premium) DIMMS (enabled)
  Bank 3 contains 512 MB (Premium) DIMMS (enabled)
  Bank 4 contains 512 MB (Premium) DIMMS (enabled)
  Bank 5 contains 512 MB (Premium) DIMMS (enabled)
  Bank 6 contains 512 MB (Premium) DIMMS (enabled)
  Bank 7 contains 512 MB (Premium) DIMMS (enabled)
Memory at Module 001c03/Slot 0: 4096 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 2 contains 512 MB (Standard) DIMMS (enabled)
  Bank 3 contains 512 MB (Standard) DIMMS (enabled)
  Bank 4 contains 512 MB (Standard) DIMMS (enabled)
  Bank 5 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
  CDROM: unit 0 on SCSI controller 2
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3/IOC4 serial port: tty5
IOC3/IOC4 serial port: tty6
Graphics board: SG2
Graphics board: SG2
Integral Gigabit Ethernet: tg0, module 001c02, PCI bus 1 slot 4
Iris Audio Processor: version MAD revision 1, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
  PCI Adapter ID (vendor 0x1002, device 0x4e47) PCI slot 1
  PCI Adapter ID (vendor 0x1002, device 0x4e67) PCI slot 1
  PCI Adapter ID (vendor 0x1002, device 0x4e47) PCI slot 1
  PCI Adapter ID (vendor 0x1002, device 0x4e67) PCI slot 1
  PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2
IOC4 firmware revision 83
IOC3/IOC4 external interrupts: 1
HUB in Module 001c02/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
HUB in Module 001c03/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c02/Slot n0: Revision 6.210
IP35prom in Module 001c03/Slot n0: Revision 6.210


Code: Select all

# uname -aR
IRIX64 last 6.5 6.5.25f 07080049 IP35


Code: Select all

# /usr/gfx/gfxinfo
Graphics board 0 is "SG2" graphics.
   Managed (":0.0") 1280x1024
   Memory Size: 128 MB

   Channel 0:
    Origin = (0,0)
    Video Output: 1280 pixels, 1024 lines, 75.02Hz (1280x1024)
Graphics board 1 is "SG2" graphics.
   Managed (":0.1") 1280x1024
   Memory Size: 128 MB

   Channel 0:
    Origin = (0,0)
    Video Output: 1280 pixels, 1024 lines, 85.02Hz (1280x1024)


I have yet to manage to get V12 or DM3 to work properly in a CPU-less chassic due to issues with FAN speeds, that result in machine shutting down before boot completes. So I have also recorded the l1 env result to try to see what is happening with fans on this test:

Code: Select all

001c02-L1>env
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
          1.8V    Enabled  10%   1.62/  1.98  20%   1.44/  2.16    1.78
           12V <not present>
        12V #2    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
        5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.02
      3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.29
    PCI 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.02
      PCI 3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32
      PCI 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
        PCI 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.94
  XIO 12V BIAS <not present>
        XIO 5V <not present>
      XIO 2.5V <not present>
  XIO 3.3V AUX <not present>
 IP59 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.29
   IP59 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04
      IP59 12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00
     IP59 VCPU    Enabled  10%   1.15/  1.40  20%   1.02/  1.53    1.25
     IP59 SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.47
     IP59 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49

Description     State       Warning RPM  Current RPM
--------------- ----------  -----------  -----------
FAN  0  EXHST 1    Enabled         2160         2295
FAN  1  EXHST 2    Enabled         2160         2295
FAN  2       PS    Enabled         3200         4066
FAN  3    PCI 1    Enabled         2160         2576
FAN  4    PCI 2    Enabled         2160         2836
FAN  5  N0 LEFT    Enabled         2160         3125
FAN  6  N0 CNTR    Enabled         2160         2884
FAN  7 N0 RIGHT    Enabled         2160         3125

                              Advisory   Critical   Fault      Current
Description       State       Temp       Temp       Temp       Temp       
----------------- ----------  ---------  ---------  ---------  --------- 
 0 INTERFACE 0       Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 1 INTERFACE 1       Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 2 INTERFACE 2       Enabled   31C/ 87F   48C/118F   55C/131F   23C/ 73F
 3 PCI RISER         Enabled   31C/ 87F   48C/118F   55C/131F   20C/ 68F
 4 ODYSSEY        <not present>
 5 NODE              Enabled   31C/ 87F   48C/118F   55C/131F   20C/ 68F
 6 BEDROCK           Enabled   31C/ 87F   48C/118F   55C/131F   17C/ 62F

001c03-L1>env
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
          1.8V    Enabled  10%   1.62/  1.98  20%   1.44/  2.16    1.79
           12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
        12V #2    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00
        5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.07
      3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.25
    PCI 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.07
      PCI 3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.30
      PCI 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.51
        PCI 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.91
  XIO 12V BIAS <not present>
        XIO 5V <not present>
      XIO 2.5V <not present>
  XIO 3.3V AUX <not present>
 IP53 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.23
   IP53 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04
      IP53 12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00
     IP53 VCPU    Enabled  10%   1.13/  1.38  20%   1.00/  1.50    1.24
     IP53 SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.47
     IP53 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49

Description     State       Warning RPM  Current RPM
--------------- ----------  -----------  -----------
FAN  0  EXHST 1    Enabled         2160         3183
FAN  1       PS    Enabled         3200         5357
FAN  2    PCI 1    Enabled         1980         2250
FAN  3    PCI 2    Enabled         1980         2445

                              Advisory   Critical   Fault      Current
Description       State       Temp       Temp       Temp       Temp       
----------------- ----------  ---------  ---------  ---------  --------- 
 0 INTERFACE 0       Enabled    [Autofan Control]    75C/167F   49C/120F
 1 INTERFACE 1       Enabled    [Autofan Control]    75C/167F   48C/118F
 2 INTERFACE 2       Enabled    [Autofan Control]    75C/167F   41C/105F
 3 PCI RISER         Enabled    [Autofan Control]    75C/167F   32C/ 89F
 4 ODYSSEY        <not present>
 5 NODE              Enabled    [Autofan Control]    75C/167F   35C/ 95F
 6 BEDROCK           Enabled    [Autofan Control]    85C/185F   61C/141F

                     Zone Temp     Target    Current   Zone Fan   Curr/Min
Zone Name  State     Sensors       Average   Average   Index      Fan %
---------  --------  ------------  --------  --------  ---------  ---------
EXHST       Enabled     0,1,2,5,6  47C/116F  46C/114F          0   41%/ 18%
PS          Enabled     0,1,2,5,6  47C/116F  46C/114F          1   67%/ 55%
AGP         Enabled             3  40C/104F  32C/ 89F        2,3   55%/ 55%




Getting to this stage took quite a long time as I once more went from using IRIX 6.5.21 then updated the up to 6.5.25 to ensure I got SW installed correctly.

I have still not managed to Get V12 or DM3 working in standalone chassis.....
Am thinking now that I will keep Tezro board in the Onyx 4 to make G2N.

Cheers, from Australia.


jwhat.

[jwhat]

Nekochaners,

here is picture of G2 upgraded to G2N:



And here is rather primitive SG2 graphics following initial 6.5.21 install:



I ended up doing 2 IRIX installs as first one had too many issues.

One of problems is that SG2 graphics initialisation uses a perl script in /etc/rc.2.d and the first install did not include perl, so script failed and so I got no graphics.

In the second install I added extra distribution of fw_perl (may_04 version) into install and things went much better.

Also as I added the board from Tezro into the G2 to make the G2N I needed to purchase a new set of longer screws as the Tezro screws are too short for Orgin/Onyx. FYI the right screw size for securing down the processor board are: M4 x 20mm (+ washers).

Here is 4 x 1G/4 x 700MHz machines moved down into basement... I am not going to do much more work on this pair for now as I need to get V12/DM3 setup working with other pair.



Cheers from Oz.


jwhat

[jwhat]

Hi Nekochaners,

as per dubious thread: viewtopic.php?f=14&t=16732561

Here is updated hinv of Onyx4 with ATI Graphics as part of split up of 5 Chimera chassis:

Code: Select all

Location: /hw/module/001c03/node
       IP59_4CPU Board: barcode RMB786     part 030-1989-003 rev -D
Location: /hw/module/001c03/CGbrick/xtalk/10
       2U_INT_53 Board: barcode NLA195     part 030-1809-006 rev -B
Location: /hw/module/001c03/IXbrick/xtalk/15
       2U_INT_53 Board: barcode NCA858     part 030-1809-003 rev -B
Location: /hw/module/001c03/IXbrick/xtalk/15/pci-x/0/1/ioc4
             IO9 Board: barcode RAD764     part 030-1771-006 rev -A
Location: /hw/module/001c03/IXbrick/xtalk/15/pci-x/1/1
     PCI_SIO_UFC Board: barcode NFD033     part 030-1657-003 rev  A
Location: /hw/module/001c04/node
       IP59_4CPU Board: barcode RAG401     part 030-1989-003 rev -C
Location: /hw/module/001c04/IXbrick/xtalk/15
       2U_INT_53 Board: barcode RHM011     part 030-1809-006 rev -D
Location: /hw/module/001c04/IXbrick/xtalk/15/pci-x/0/1/ioc4
             IO9 Board: barcode NFV336     part 030-1771-005 rev -A
8 1.0 GHZ IP35 Processors
CPU: MIPS R16000 Processor Chip Revision: 3.0
FPU: MIPS R16010 Floating Point Chip Revision: 3.0
CPU 0 at Module 001c03/Slot 0/Slice A: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 1 at Module 001c03/Slot 0/Slice B: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 2 at Module 001c03/Slot 0/Slice C: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 3 at Module 001c03/Slot 0/Slice D: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 4 at Module 001c04/Slot 0/Slice A: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 5 at Module 001c04/Slot 0/Slice B: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 6 at Module 001c04/Slot 0/Slice C: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 7 at Module 001c04/Slot 0/Slice D: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
Main memory size: 16384 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 16 Mbytes
Memory at Module 001c03/Slot 0: 8192 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 4 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 5 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 6 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 7 contains 1024 MB (Premium) DIMMS (enabled)
Memory at Module 001c04/Slot 0: 8192 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 4 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 5 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 6 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 7 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 3: Version IDE (ATA/ATAPI) IOC4
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
  CDROM: unit 0 on SCSI controller 2
Integral SCSI controller 4: Version QL12160, low voltage differential
Integral SCSI controller 5: Version QL12160, low voltage differential
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
Integral SCSI controller 1: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty15
IOC3/IOC4 serial port: tty16
IOC3/IOC4 serial port: tty17
IOC3/IOC4 serial port: tty18
IOC3/IOC4 serial port: tty9
IOC3/IOC4 serial port: tty10
IOC3/IOC4 serial port: tty11
IOC3/IOC4 serial port: tty12
IOC3/IOC4 serial port: tty13
IOC3/IOC4 serial port: tty14
Graphics board: SG2
Graphics board: SG2
Gigabit Ethernet: tg1, module 001c04, PCI bus 1 slot 4
Integral Gigabit Ethernet: tg0, module 001c03, PCI bus 1 slot 4
Iris Audio Processor: version MAD revision 1, number 2
  PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
  PCI Adapter ID (vendor 0x1002, device 0x4e47) PCI slot 1
  PCI Adapter ID (vendor 0x1002, device 0x4e67) PCI slot 1
  PCI Adapter ID (vendor 0x1002, device 0x4e47) PCI slot 1
  PCI Adapter ID (vendor 0x1002, device 0x4e67) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 1
  PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2
IOC4 firmware revision 79
IOC4 firmware revision 83
IOC3/IOC4 external interrupts: 2
IOC3/IOC4 external interrupts: 1
HUB in Module 001c03/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
HUB in Module 001c04/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c03/Slot n0: Revision 6.210
IP35prom in Module 001c04/Slot n0: Revision 6.210


And L1 env (via L2 controller), all five chassis set with same serial number but slots 1 & 2 are V12/DM3 pair and slots 3, 4 & 5 are 1GHz set + ATI/Voyager graphics:

Code: Select all

M2004476-001-L2>env
001c03:
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
          1.8V    Enabled  10%   1.62/  1.98  20%   1.44/  2.16    1.777
           12V <not present>
        12V #2    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.000
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.320
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.063
        5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.018
      3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285
    PCI 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.018
      PCI 3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.320
      PCI 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.496
        PCI 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.940
  XIO 12V BIAS <not present>
        XIO 5V <not present>
      XIO 2.5V <not present>
  XIO 3.3V AUX <not present>
 IP59 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285
   IP59 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.044
      IP59 12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.000
     IP59 VCPU    Enabled  10%   1.14/  1.40  20%   1.02/  1.52    1.283
     IP59 SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.470
     IP59 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.495

Description     State       Warning RPM  Current RPM
--------------- ----------  -----------  -----------
FAN  0  EXHST 1    Enabled         1980         2636
FAN  1  EXHST 2    Enabled         1980         2636
FAN  2       PS    Enabled         3200         4017
FAN  3    PCI 1    Enabled         1980         2576
FAN  4    PCI 2    Enabled         1980         2836
FAN  5  N0 LEFT    Enabled         1980         4054
FAN  6  N0 CNTR    Enabled         1980         3750
FAN  7 N0 RIGHT    Enabled         1980         4109

                              Advisory   Critical   Fault      Current     
Description       State       Temp       Temp       Temp       Temp       
----------------- ----------  ---------  ---------  ---------  --------- 
 0 INTERFACE 0       Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 1 INTERFACE 1       Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 2 INTERFACE 2       Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 3 PCI RISER         Enabled   31C/ 87F   48C/118F   55C/131F   20C/ 68F
 4 ODYSSEY        <not present>
 5 NODE              Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 6 BEDROCK           Enabled   31C/ 87F   48C/118F   55C/131F   19C/ 66F

001c04:
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
          1.8V    Enabled  10%   1.62/  1.98  20%   1.44/  2.16    1.777
           12V <not present>
        12V #2    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.000
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.337
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.000
        5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.044
      3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.302
    PCI 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.070
      PCI 3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.320
      PCI 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.509
        PCI 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.966
  XIO 12V BIAS <not present>
        XIO 5V <not present>
      XIO 2.5V <not present>
  XIO 3.3V AUX <not present>
 IP59 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.302
   IP59 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.044
      IP59 12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.938
     IP59 VCPU    Enabled  10%   1.14/  1.40  20%   1.02/  1.52    1.283
     IP59 SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.470
     IP59 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.495

Description     State       Warning RPM  Current RPM
--------------- ----------  -----------  -----------
FAN  0  EXHST 1    Enabled         1980         2721
FAN  1  EXHST 2    Enabled         1980         2700
FAN  2       PS    Enabled         3200         4821
FAN  3    PCI 1    Enabled         1980         2636
FAN  4    PCI 2    Enabled         1980         2909
FAN  5  N0 LEFT    Enabled         1980         3947
FAN  6  N0 CNTR    Enabled         1980         3797
FAN  7 N0 RIGHT    Enabled         1980         4054

                              Advisory   Critical   Fault      Current     
Description       State       Temp       Temp       Temp       Temp       
----------------- ----------  ---------  ---------  ---------  --------- 
 0 INTERFACE 0       Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 1 INTERFACE 1       Enabled   31C/ 87F   48C/118F   55C/131F   17C/ 62F
 2 INTERFACE 2       Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 3 PCI RISER         Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F
 4 ODYSSEY        <not present>
 5 NODE              Enabled   31C/ 87F   48C/118F   55C/131F   17C/ 62F
 6 BEDROCK           Enabled   31C/ 87F   48C/118F   55C/131F   18C/ 64F

001v05:
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
          1.8V    Enabled  10%   1.62/  1.98  20%   1.44/  2.16    1.791
           12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.063
        12V #2    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.063
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.320
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.063
        5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.070
      3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.251
    PCI 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096
      PCI 3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285
      PCI 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.509
        PCI 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.914
  XIO 12V BIAS <not present>
        XIO 5V <not present>
      XIO 2.5V <not present>
  XIO 3.3V AUX <not present>
 IP53 3.3V AUX <not present>
   IP53 5V AUX <not present>
      IP53 12V <not present>
     IP53 VCPU <not present>
     IP53 SRAM <not present>
     IP53 1.5V <not present>

Description     State       Warning RPM  Current RPM
--------------- ----------  -----------  -----------
FAN  0  EXHST 1    Enabled         1350         1864
FAN  1       PS    Enabled         3200         4218
FAN  2    PCI 1    Enabled         1980         2235
FAN  3    PCI 2    Enabled         1980         2463

                              Advisory   Critical   Fault      Current     
Description       State       Temp       Temp       Temp       Temp       
----------------- ----------  ---------  ---------  ---------  --------- 
 0 INTERFACE 0       Enabled   50C/122F   54C/129F   58C/136F   35C/ 95F
 1 INTERFACE 1       Enabled   50C/122F   54C/129F   58C/136F   38C/100F
 2 INTERFACE 2       Enabled   50C/122F   54C/129F   58C/136F   32C/ 89F
 3 PCI RISER         Enabled   50C/122F   54C/129F   58C/136F   29C/ 84F
 4 ODYSSEY        <not present>
 5 NODE           <not present>
 6 BEDROCK        <not present>
 

And pictures...

Rack with all the Origin350/Onyx350/4 boxes, VBOB and L2



Now I have physical configuration settled will work on getting VBOB going and IRIX updated to include updated IRIX & MIPSPro C/C++ installs.

This lot is now pretty much back to where they started when originally shipped (8x1GHz + ATI) to Oz by Mopar and I started to slice and dice across the various chassis to try to get a 4x1GHz + V12 + DM3 configuration up and running.

Now accepting that this is not possible without either: Numalink Router, V-Brick or possibly IP53_0CPU board.

Cheers from Oz,

jwhat.