Page 1 of 1

Octane ESI / R12000 300Mhz / 512MB / CAD-Duo

Posted: Tue Apr 11, 2017 3:32 pm
by vmul
Hello folks. Been a very long time since I've been anywhere near SGI hardware but I recently found a nice, tidy Octane setup so decided to grab and have a play. Here she is : https://i.imgur.com/8gOhUHi.jpg

It arrived with a 36GB Barracuda in an external SCSI enclosure (https://i.imgur.com/NgBeFmH.png), and has a bunch of DALiM software on it (LiTHO et al) .. along with what looks like the sprawling remnants of a graphic design company - 8GB of DTP files for clients like AVON and the RSPB. Most bizarre.

The installed-software list is over here for the interested: https://pastebin.com/raw/6NtXX4EK - the Barracuda seemed to house a mirror of the install CDs + a large set of DALiM install packages.

Here's the pile of stats! + a couple of Q's for the more enlightened...

- the serial for the IP30, 030-1467-001, suggests it is a later revision but it has a black handle. Is that normal?
- XTALKPCI 030-0952-005 - is that an SGI PCI cage? if so, that is what the "CAD-Duo" card honking out the back (https://i.imgur.com/YXzdLCS.png) is plugged into, right?

HINV -VM

Code: Select all

IRIX64 OCTANE 6.5 10181058 IP30 - Serial 0800 6913 06C7

Location: /hw/node
      PM10300MHZ Board: barcode JLC578     part 030-1355-001 rev  M
Location: /hw/node/xtalk/15
            IP30 Board: barcode JZD419     part 030-1467-001 rev  D
Location: /hw/node/xtalk/15/pci/2
    PWR.SPPLY.ER Board: barcode AAE9380384 part 060-0035-002 rev  A
             FP1 Board: barcode KBX446     part 030-0891-003 rev  F
Location: /hw/node/xtalk/13
        XTALKPCI Board: barcode ESG189     part 030-0952-005 rev  A
Location: /hw/node/xtalk/13/pci/2
        PCI_ENET Board: barcode HKC092     part 030-1155-002 rev  D
Location: /hw/node/xtalk/12
           MOT10 Board: barcode JJF578     part 030-1241-002 rev  J
1 300 MHZ IP30 Processor
CPU: MIPS R12000 Processor Chip Revision: 2.3
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 512 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3 serial port: tty1
IOC3 serial port: tty2
IOC3 parallel port: plp1
Graphics board: ESI
Integral Fast Ethernet: ef0, version 1, pci 2
Fast Ethernet: ef1, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 4265, device 3) pci slot 2
  PCI Adapter ID (vendor 4215, device 4128) pci slot 0
  PCI Adapter ID (vendor 4215, device 4128) pci slot 1
  PCI Adapter ID (vendor 4265, device 5) pci slot 3
  PCI Adapter ID (vendor 4265, device 3) pci slot 2


GFXINFO

Code: Select all

Graphics board 0 is "IMPACTSR" graphics.
   Managed (":0.0") 1280x1024
   Product ID 0x2, 1 GE, 1 RE, 0 TRAMs
   MGRAS revision 4, RA revision 0
   HQ rev B, GE12 rev A, RE4 rev C, PP1 rev G,
   VC3 rev A, CMAP rev F, Heart rev F
   20" monitor (id 0x3)

   Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
   Channel 0:
    Origin = (0,0)
    Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)
    Video Format Flags:  (none)
    Sync Disabled
    Using Gamma Map 0
    Monitor Type:  unknown


SCSI -I (not including the external, I didn't have it powered on at the time)

Code: Select all

/dev/scsi/sc0d1l0:  Disk          SGI     IBM DNES-309170YSA30
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready

Re: Octane ESI / R12000 300Mhz / 512MB

Posted: Tue Apr 11, 2017 4:15 pm
by japes
PCI Card Cage hanging out the back (nickname shoebox) with a IOC3 or CADduo card. Since you have only a single graphics board I imagine it was added to provide a second ethernet port.