Got this from recondas over the weekend, finally got it somewhat configured (SSH, Samba etc) and swapped out the 4x256mb sticks for 4x512mb sticks that I had laying around.
hinv -vmCode:
Location: /hw/module/001c01/node
IP34 Board: barcode NCL405 part 030-1707-004 rev -A
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode NCL237 part 030-1730-002 rev -E
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODYV10 Board: barcode NNJ828 part 030-1826-003 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode NCL405 part 030-1707-004 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode NCL405 part 030-1707-004 rev -A
1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.4
FPU: MIPS R14010 Floating Point Chip Revision: 2.4
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz Tap 0xa
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 2048 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V10
Gigabit Ethernet: tg1, module 001c01, PCI bus 2 slot 1
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version EMU revision A3, number 1
PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 1
PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 2
PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
USB controller: type OHCI
USB Human Interface Device: device id 0 type keyboard
USB Human Interface Device: device id 0 type mouse
/usr/gfx/gfxinfoCode:
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 1280x1024
BUZZ version B.2
PB&J version 1
32MB memory
Banks: 2, CAS latency: 3
Monitor 0 type: ACR -21132
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)
Next up is getting a vfo for 1680x1050x16@60hz working...
_________________

33mhz R3k/48mb/XS24

150mhz R4400/256mb/XL24

600mhz R14kA/2gb/V10

8x1.4ghz Itanium 2/8GB

32x600mhz R14kA/24GB

4x700mhz R16k/8GB/V12/DCD/SAS/FC/DM5

2x700mhz R16k/4GB