Nekochan Net

Official Chat Channel: #nekochan // irc.nekochan.net
It is currently Tue Nov 25, 2014 11:21 pm

All times are UTC - 8 hours [ DST ]


Forum rules


Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.



Post new topic Reply to topic  [ 1 post ] 
Author Message
Unread postPosted: Sat Oct 15, 2011 3:57 am 
Offline

Joined: Tue Apr 19, 2011 4:59 am
Posts: 150
Location: Yorkshire, UK
Original spec when acquired, August 2011: R16K 700MHz, 1024MB RAM (4x256 standard), V10, 73GB HDs
UPDATE September 2011: replaced 73GB with two 146GB HDDs
UPDATE January 2012: RAM upgrade, soundcard
PCI cards are LSI 20320-HP, Creative SB0090 soundcard and Belkin F5U220 USB.
UPDATE September 2012: Belkin F5U503 Firewire card and 1TB external disk
LSI 21320 to replace LSI 20320-HP (for more usefully positioned sockets)
UPDATE May 2013: replaced V10 (030-1826-003 rev -A) with V12 (ex-Tezro)
UPDATE March 2014: tried Adaptec Duoconnect AUA-3020 without success-
UPDATE March 2014: replaced USB card with narrow SCSI socket cabled to Channel B on the LSI 21320, to drive a slide scanner (Nikon Coolscan II, seems fine with xsane from nekoware)

Hinv etc from May 2013 after fitting the V12:
hinv -vm
Code:
Location: /hw/module/001c01/node
            IP34 Board: barcode NAS621     part 030-1707-003 rev -M
Location: /hw/module/001c01/node/cpubus/0
        IP34PIMM Board: barcode MSY420     part 030-1891-001 rev -D
Location: /hw/module/001c01/Ibrick/xtalk/13
      ODY128B1_2 Board: barcode NWM092     part 030-1884-005 rev -B
Location: /hw/module/001c01/Ibrick/xtalk/14
            IP34 Board: barcode NAS621     part 030-1707-003 rev -M
Location: /hw/module/001c01/Ibrick/xtalk/15
            IP34 Board: barcode NAS621     part 030-1707-003 rev -M
1 700 MHZ IP35 Processor
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xa
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 6: Version IEEE1394 SBP2
Integral SCSI controller 7: Version LS1030, low voltage differential
Integral SCSI controller 8: Version LS1030, low voltage differential
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, single ended
  CDROM: unit 4 on SCSI controller 1
  Disk drive / removable media: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version EMU revision A3, number 1
  PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
  PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
  PCI Adapter ID (vendor 0x1033, device 0x00e0) PCI slot 1
  PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
  PCI Adapter ID (vendor 0x1000, device 0x0030) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 2
  PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 2
  PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 2
  PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 3
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
USB controller: type OHCI
USB controller: type OHCI


gfxinfo
Code:
Graphics board 0 is "ODYSSEY" graphics.
   Managed (":0.0") 1920x1200
   BUZZ version B.2
   PB&J version 1
   128MB memory
      Banks: 4, CAS latency: 3
    Monitor 0 type: GSM 8704
   Channel 0:
    Origin = (0,0)
    Video Output: 1920 pixels, 1200 lines, 60.00Hz (1920x1200_60p.vfo)

The "GSM8704" is in this case a TV - 22LG3000 - connected using DVI-HDMI; my Pi uses the other HDMI input and there is also a VGA input for the Indigo2, RiscPC and EspressoPC. This replaced an Iiyama 9017 CRT when we got a new TV!

uname -aR reports "IRIX64 redbox 6.5 6.5.30m 07202013 IP35"

scsicontrol -v
Code:
/dev/scsi/sc0d1l0:  Disk          FUJITSU MAP3147NP       5605
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc1d4l0:  CD-ROM        TOSHIBA DVD-ROM SD-M14011007
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch linkedcmds
Device is  not ready
/dev/scsi/sc1d6l0:  Disk          SyQuest SQ3270S         3_05
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch linkedcmds
Device is  not ready


The Syquest shows "Device is not ready" as there is no cartridge present - it seems to operate very nicely, mounting automatically when a cartridge is inserted and unmounting from the "Eject" option on the menu.

I also have a second 146GB drive fitted but only connect power when wanting to back up. The Fujitsu is set to spin up on command rather than power-on, so PROM-only operations can happen without wear on the drive (handy when fitting / troubleshooting other hardware!).

L1 info - for some reason I cannot get anything from "l1cmd pci" although I am sure this has worked in the past.

l1cmd flash status
Code:
Flash image A currently booted

Image      Status        Revision    Built
-----   -------------   ----------   -----
  A     user default    1.44.0       07/17/2006 18:20:38
  B     valid           1.44.0       07/17/2006 18:20:38


l1cmd serial all
Code:
Data                            Location      Value
------------------------------  ------------  --------
Local System Serial Number      EEPROM        08:00:69:10:6F:CB
Local Brick Serial Number       EEPROM        NAS621
Reference Brick Serial Number   NVRAM         NAS621


EEPROM      Product Name    Serial         Part Number           Rev  T/W   
----------  --------------  -------------  --------------------  ---  ------
NODE        IP34            NAS621         030_1707_003          M    00   
MAC         MAC ADDRESS     NA             NA                    NA   NA   
PIMM        IP34PIMM        MSY420         030_1891_001          D    00   
XIO         ODY128B1_2       NWM092         030_1884_005          B    00   

EEPROM     JEDEC-SPD Info           Part Number        Rev  Speed  SGI     
---------- ------------------------ ------------------ ---- ------ --------
DIMM 0     CE000000000000000C9B0F00 M3 46L2820DT2-CA0   2D   10.0  N/A     
DIMM 2     CE0000000000000028181900 M3 46L2820BT1-CA0   0B    8.0  N/A     
DIMM 1     CE000000000000000C5F0B00 M3 46L2820DT2-CA0   2D   10.0  N/A     
DIMM 3     CE0000000000000027CE1400 M3 46L2820BT1-CA0   0B    8.0  N/A     


l1cmd env
Code:
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
           12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.063
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125
            5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.096
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.337
          2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.470
          1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.466
        5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.122
      3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285
 PIMM 12V BIAS    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.125
          SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.522
          VCPU    Enabled  10%   1.13/  1.38  20%   1.00/  1.50    1.241
     PIMM 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.495
 PIMM 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285
   PIMM 5V AUX    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.122
  XIO 12V BIAS    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   11.938
        XIO 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.070
      XIO 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.457
  XIO 3.3V AUX    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.285

Description     State       Warning RPM  Current RPM
--------------- ----------  -----------  -----------
FAN  0  EXHAUST    Enabled          920         1188
FAN  1       HD    Enabled         1560         2280
FAN  2      PCI    Enabled         1120         1562
FAN  3    XIO 1    Enabled         1600         2463
FAN  4    XIO 2    Enabled         1600         2376
FAN  5       PS    Enabled         1349         3308

                              Advisory   Critical   Fault      Current     
Description       State       Temp       Temp       Temp       Temp       
----------------- ----------  ---------  ---------  ---------  --------- 
 0 NODE 0            Enabled    [Autofan Control]    80C/176F   35C/ 95F
 1 NODE 1            Enabled    [Autofan Control]    80C/176F   39C/102F
 2 NODE 2            Enabled    [Autofan Control]    80C/176F   28C/ 82F
 3 PIMM              Enabled    [Autofan Control]    80C/176F   41C/105F
 4 ODYSSEY           Enabled    [Autofan Control]    80C/176F   44C/111F
 5 BEDROCK           Enabled    [Autofan Control]    85C/185F   39C/102F

The V10 used to run at 38C, so 44C after an hour's use (and the PIMM at 2C wamer) was a very slight concern, but the fans seem only slightly faster. It was January 2012 when I last put env output in this entry, quite possibly at night so the ambient temperature may have been several degrees lower (the Fuel is in a north-facing corner room). Checking again later, the V12 and PIMM were both down a couple of degrees AND the fans were slower, so I should stop worrying!

_________________
Fuel; Indigo2; RiscPC Kinetic-StrongARM RISCOS 4.39 or Debian/sarge; EspressoPC ViaC3/900 Debian-testing; RPi B RISCOS5.21 or Raspbian/jessie


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group