Fuel: 600MHz | V10 | 1GB | EMU Audio | gigE | DDS4

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
User avatar
recondas
Moderator
Moderator
Posts: 5442
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Fuel: 600MHz | V10 | 1GB | EMU Audio | gigE | DDS4

Unread postby recondas » Fri Jul 15, 2011 3:54 pm

Code: Select all

hinv -vm
Location: /hw/module/001c01/node
            IP34 Board: barcode NCL381     part 030-1707-004 rev -A
Location: /hw/module/001c01/node/cpubus/0
        IP34PIMM Board: barcode NCL234     part 030-1730-002 rev -E
Location: /hw/module/001c01/Ibrick/xtalk/13
       ASTODYV10 Board: barcode NAT111     part 030-1826-001 rev -B
Location: /hw/module/001c01/Ibrick/xtalk/14
            IP34 Board: barcode NCL381     part 030-1707-004 rev -A
Location: /hw/module/001c01/Ibrick/xtalk/15
            IP34 Board: barcode NCL381     part 030-1707-004 rev -A
1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.4
FPU: MIPS R14010 Floating Point Chip Revision: 2.4
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
  Processor revision: 2.4. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
Main memory size: 3072 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 1536 MB (enabled)
  Bank 0 contains 512 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Disk drive: unit 3 on SCSI controller 0 (unit 3)
  Tape drive: unit 6 on SCSI controller 0: DAT
Integral SCSI controller 1: Version QL12160, single ended
  CDROM: unit 6 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V10
Gigabit Ethernet: eg0, module 001c01, pci_bus 2, pci_slot 2, firmware version 0.0.0
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version EMU revision A3, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0009) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  PCI Adapter ID (vendor 0x1102, device 0x0004) PCI slot 3
  PCI Adapter ID (vendor 0x1102, device 0x7003) PCI slot 3
  PCI Adapter ID (vendor 0x1102, device 0x4001) PCI slot 3
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  PCI Adapter ID (vendor 0x1045, device 0xc861) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
USB controller: type OHCI
USB Human Interface Device: device id 0 type mouse
USB Human Interface Device: device id 0 type keyboard

Code: Select all

/usr/gfx/gfxinfo -v
Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 1600x1200
        BUZZ version B.1
        PB&J version 1
        32MB memory
                Banks: 2, CAS latency: 3
         Monitor 0 type: Unknown
        Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
        Channel 0:
         Origin = (0,0)
         Video Output: 1600 pixels, 1200 lines, 59.83Hz (1600x1200_60)
         Video Format Flags:  (none)
         Sync Disabled
         Using Gamma Map 0

Code: Select all

# l1cmd serial all

Data                            Location      Value
------------------------------  ------------  --------
Local System Serial Number      EEPROM        08:00:69:10:72:F2
Local Brick Serial Number       EEPROM        NCL381
Reference Brick Serial Number   NVRAM         NCL381


EEPROM      Product Name    Serial         Part Number           Rev  T/W   
----------  --------------  -------------  --------------------  ---  ------
NODE        IP34            NCL381         030_1707_004          A    00   
MAC         MAC ADDRESS     NA             NA                    NA   NA   
PIMM        IP34PIMM        NCL234         030_1730_002          E    00   
XIO         ASTODYV10       NAT111         030_1826_001          B    00   

EEPROM     JEDEC-SPD Info           Part Number        Rev  Speed  SGI
---------- ------------------------ ------------------ ---- ------ --------
DIMM 0     CE000000000000000C44CD02 M3 46L3313ET3-CA0   3E    10.0  N/A
DIMM 2     CE000000000000000C3B0000 M3 47L6423DT2-CA0   3E    10.0  N/A
DIMM 1     CE000000000000000C39CD02 M3 46L3313ET3-CA0   3E    10.0  N/A
DIMM 3     CE000000000000000C730100 M3 47L6423DT2-CA0   3E    10.0  N/A

Code: Select all

# l1cmd env
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
           12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.19
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.19
            5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.02
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32
          2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.47
          1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.47
        5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.10
      3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27
PIMM0 12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.19
     Fuel SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.52
      Fuel CPU    Enabled  10%   1.44/  1.76  20%   1.28/  1.92    1.59
    PIMM0 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.48
PIMM0 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27
  PIMM0 5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.07
  XIO 12V bias    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
        XIO 5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.02
      XIO 2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.46
  XIO 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.30

Description    State       Warning RPM  Current RPM
-------------- ----------  -----------  -----------
FAN 0  EXHAUST    Enabled          920         1155
FAN 1       HD    Enabled         1560         2250
FAN 2      PCI    Enabled         1120         1591
FAN 3    XIO 1    Enabled         1600         2596
FAN 4    XIO 2    Enabled         1600         2481
FAN 5       PS    Enabled         1349         3183

                              Advisory   Critical   Fault      Current
Description       State       Temp       Temp       Temp       Temp       
----------------- ----------  ---------  ---------  ---------  --------- 
 0 NODE 0            Enabled    [Autofan Control]    75C/167F   44C/111F
 1 NODE 1            Enabled    [Autofan Control]    75C/167F   44C/111F
 2 NODE 2            Enabled    [Autofan Control]    75C/167F   35C/ 95F
 3 PIMM              Enabled    [Autofan Control]    75C/167F   53C/127F
 4 ODYSSEY           Enabled    [Autofan Control]    75C/167F   44C/111F
 5 BEDROCK           Enabled    [Autofan Control]    85C/185F   46C/114F

Code: Select all

uname -aR
IRIX64 IRIS 6.5 6.5.30f 07202013 IP35

Code: Select all

scsicontrol -i /dev/scsi/*
/dev/scsi/sc0d1l0:  Disk          SEAGATE ST336753LW      0006
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc0d3l0:  Disk          SEAGATE ST3300007LW      0003
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc0d6l0:  Tape          SEAGATE DAT    06240-XXX8160
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds
Device is ready

/dev/scsi/sc1d6l0:  CD-ROM        TOSHIBA DVD-ROM SD-M17111005
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch linkedcmds
Device is ready

Code: Select all

1cmd flash status
Flash image B currently booted

Image      Status        Revision    Built
-----   -------------   ----------   -----
  A     valid           1.26.5       12/15/2003 12:57:41
  B     default         1.26.5       12/15/2003 12:57:41
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************

User avatar
Titox
Posts: 265
Joined: Tue Aug 14, 2007 12:13 am
Location: Spain

Re: Fuel: 600MHz | V10 | 1.5GB | EMU Audio | gigE | DDS4

Unread postby Titox » Sat Jul 16, 2011 12:32 am

Nice machine. I see you have a Seagate DAT drive. I thought only Sony models were compatible with SGI. Can anyone add to the Fuel Hardware aggregator a list of compatible DDS's?

Thank you
Alberto (Between the TV and the sofa)
:Fuel: :Octane2: :1600SW: :O2: :O2: :1600SW: :Indigo:
http://www.f3b.es
http://unixverse.blogspot.com

gambonyx
Posts: 159
Joined: Sun Apr 10, 2011 3:25 am

Re: Fuel: 600MHz | V10 | 1.5GB | EMU Audio | gigE | DDS4

Unread postby gambonyx » Sat Jul 16, 2011 3:27 am

Nice fuel!
I have a question to ask, but the Rams should not be in ascending order on the bank?
Does nothing if the bank 0/1 is - 256 and the bank 2/3 - 512?

User avatar
recondas
Moderator
Moderator
Posts: 5442
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Re: Fuel: 600MHz | V10 | 1.5GB | EMU Audio | gigE | DDS4

Unread postby recondas » Sat Jul 16, 2011 4:27 am

Titox wrote:Nice machine.
Thanks
Titox wrote:I see you have a Seagate DAT drive. I thought only Sony models were compatible with SGI. Can anyone add to the Fuel Hardware aggregator a list of compatible DDS's?
That's easy enough - they're *all* compatible (with a minimal amount of end-user effort). This nekowiki article explains the basic process of modifying or adding to IRIX's list of tape definitions (or drivers. If you prefer). There's also a list of definitions for a few higher capacity tape drives (LTO, SDLT and DTF) in this thread: viewtopic.php?f=3&t=16724885

gambonyx wrote:Nice fuel!
Thanks
gambonyx wrote:I have a question to ask, but the Rams should not be in ascending order on the bank? Does nothing if the bank 0/1 is - 256 and the bank 2/3 - 512?
As long as they're installed with a matching pair in either bank, size order isn't an issue (take a look at the memory configuration rules in the Fuel User's Guide), and the Fuel seems pretty happy with the arrangement - it even announces it's "running in DDR mode" during power-on diagnostics:

Code: Select all

IP35 PROM SGI Version 6.210  built 02:33:51 PM Aug 26, 2004
Running in DDR mode
Testing/Initializing memory ...............             DONE
Copying PROM code to memory ...............             DONE
Discovering local IO ......................             DONE
Discovering NUMAlink connectivity .........             DONE
Found 1 objects (1 hubs, 0 routers) in 30360 usec
Waiting for peers to complete discovery....             DONE
No other nodes present; becoming global master
Global master is /hw/rack/001/bay/01
Intializing any CPUless nodes..............             DONE
Checking partitioning information .........             DONE
No other nodes present; becoming partition master
Loading BASEIO prom .......................             DONE

BASEIO PROM Monitor SGI Version 6.210  built 02:30:38 PM Aug 26, 2004 (BE64)
1 CPUs on 1 nodes found.
Automatic update of PROM environment disabled

PS/2 Keyboard & Mouse diagnostics
    Found mouse on port 0
    Found keyboard on port 1
PS/2 Keyboard & Mouse diagnostics passed

Graphics diagnostics

Odyssey board #0 found on nasid 0
Running Odyssey xtalk sanity diag...
        Board version 1 - Buzz revision 2B
        On board sdram size: 32 Mb
        Cas latency: CAS 3
        4 banks by sdram module
Running Odyssey Buzz registers diag...
Device passed diagnostics

Installing PROM Device drivers ............             
Base I/O Ethernet set to /dev/ethernet/ef0
Installing Graphics Console...
graphics install: searching for pipe 0

Walking SCSI Adapter 0, (pci id 1)
1+ Device Vendor Product: SEAGATE ST336753LW
2- 3- 4- 5- 6+ Device Vendor Product: SEAGATE DAT    06240-XXX
7- 8- 9- 10- 11- 12- 13- 14- 15- = 2 device(s)


Walking SCSI Adapter 1, (pci id 1)
1- 2- 3- 4- 5- 6+ Device Vendor Product: TOSHIBA DVD-ROM SD-M1711
7- 8- 9- 10- 11- 12- 13- 14- 15- = 1 device(s)

Initializing PROM Device drivers ..........             DONE
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************

User avatar
GL1zdA
Donor
Donor
Posts: 429
Joined: Thu Dec 31, 2009 3:18 pm
Location: Warsaw, PL

Re: Fuel: 600MHz | V10 | 1.5GB | EMU Audio | gigE | DDS4

Unread postby GL1zdA » Sat Jul 16, 2011 4:30 am

Which EMU card is it? I assume it's EMU10K2 based (Audigy 2 ZS like)?
:PI: :Indigo: :Indigo: :Indigo: :Indy: :Indy: :Indigo2: :Indigo2IMP: :Octane: :Fuel: :540:

User avatar
recondas
Moderator
Moderator
Posts: 5442
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Re: Fuel: 600MHz | V10 | 1.5GB | EMU Audio | gigE | DDS4

Unread postby recondas » Sat Jul 16, 2011 4:36 am

GL1zdA wrote:Which EMU card is it? I assume it's EMU10K2 based (Audigy 2 ZS like)?
It's an SB0090 - a first generation Audigy Platinum EX: viewtopic.php?f=3&t=16725195&#p7340993
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************

gambonyx
Posts: 159
Joined: Sun Apr 10, 2011 3:25 am

Re: Fuel: 600MHz | V10 | 1.5GB | EMU Audio | gigE | DDS4

Unread postby gambonyx » Sat Jul 16, 2011 11:25 pm

recondas wrote:As long as they're installed with a matching pair in either bank, size order isn't an issue (take a look at the memory configuration rules in the Fuel User's Guide), and the Fuel seems pretty happy with the arrangement - it even announces it's "running in DDR mode" during power-on diagnostics:

Ok!I got it! This excerpt from the manual page of the fuel that I have indicated, that's why '
In practice one must have the same density 'memory on both the banks,
So your reads 768MB DIMM per pair of properly.
256+512 dimm pair1 /256+512 dimm pair2 ;)

The following configuration rules apply to the memory banks and DIMMs in your system:

At least one DIMM pair must be populated.

DIMMs in the same DIMM pair must be the same density. For example, if DIMM 0 is 512 MB, then DIMM 2 must be 512 MB.

DIMMs must be installed in pairs.
3-4_DIMM_sockets_pairs.gif


Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 1 guest