Nekochan Net

Official Chat Channel: #nekochan // irc.nekochan.net
It is currently Sat Nov 22, 2014 9:36 pm

All times are UTC - 8 hours [ DST ]


Forum rules


Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.



Post new topic Reply to topic  [ 3 posts ] 
Author Message
Unread postPosted: Mon Nov 14, 2011 3:15 pm 
Offline
User avatar

Joined: Sat Oct 15, 2011 4:53 pm
Posts: 11
Ok, thanks to the nice post at viewtopic.php?f=3&t=16718710&p=7342876#p7342876 I was able to get Debian 6 running on three of our four Altix boxen. This particular one is a small Altix 3700, minimum configuration in fact. Here's the hwinfo and the dmesg outputs:

Code:
roan:~# hwinfo --short
cpu:                                                           
                       Madison, 1500 MHz
                       Madison, 1500 MHz
                       Madison, 1500 MHz
                       Madison, 1500 MHz
keyboard:
  /dev/ttyS0           serial console
storage:
                       SGI IOC4 I/O controller
                       QLogic QLA12160
                       QLogic QLA2300 64-bit Fibre Channel Adapter
                       QLogic QLA2300 64-bit Fibre Channel Adapter
network:
  eth0                 SGI IO9/IO10 Gigabit Ethernet (Copper)
  eth1                 SGI Dual Port Gigabit Ethernet (PCI-X,Copper)
  eth2                 SGI Dual Port Gigabit Ethernet (PCI-X,Copper)
                       SGI Cross Partition Network adapter
network interface:
  lo                   Loopback network interface
  eth0                 Ethernet network interface
  eth2                 Ethernet network interface
  eth1                 Ethernet network interface
  pan0                 Ethernet network interface
disk:
  /dev/sda             DGC LUNZ
  /dev/sdb             DGC LUNZ
  /dev/sdd             DGC LUNZ
  /dev/sde             DGC LUNZ
  /dev/sdf             DGC LUNZ
  /dev/sdc             DGC LUNZ
  /dev/sdg             SGI ST373307LC
partition:
  /dev/sdg1            Partition
  /dev/sdg2            Partition
  /dev/sdg3            Partition
cdrom:
  /dev/hda             MATSHITADVD-ROM SR-8589
memory:
                       Main Memory
unknown:
                       Timer
                       PS/2 Controller
roan:~#


Code:
roan:~# dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.32-5-mckinley (Debian 2.6.32-38) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Mon Oct 3 06:04:14 UTC 2011
[    0.000000] EFI v1.10 by INTEL: SALsystab=0x3002a09070 ACPI 2.0=0x3002a09840
[    0.000000] booting generic kernel on platform sn2
[    0.000000] console [sn_sal0] enabled
[    0.000000] ACPI: RSDP 0000003002a09840 00024 (v02    SGI)
[    0.000000] ACPI: XSDT 0000003002a09880 00044 (v01    SGI  XSDTSN2 00010001    ? 00000001)
[    0.000000] ACPI: APIC 0000003002a098e0 0005C (v01    SGI  APICSN2 00010001    ? 00000001)
[    0.000000] ACPI: SRAT 0000003002a09950 000C0 (v01    SGI  SRATSN2 00010001    ? 00000001)
[    0.000000] ACPI: SLIT 0000003002a09a20 00030 (v01    SGI  SLITSN2 00010001    ? 00000001)
[    0.000000] ACPI: FACP 0000003002a09b00 000F4 (v03    SGI  FACPSN2 00030001    ? 00000001)
[    0.000000] ACPI Warning: 32/64X length mismatch in Pm1aEventBlock: 32/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: 32/64X length mismatch in Pm1aControlBlock: 16/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: 32/64X length mismatch in PmTimerBlock: 32/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: 32/64X length mismatch in Gpe0Block: 64/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: Invalid length for Pm1aEventBlock: 0, using default 32 (20090903/tbfadt-607)
[    0.000000] ACPI Warning: Invalid length for Pm1aControlBlock: 0, using default 16 (20090903/tbfadt-607)
[    0.000000] ACPI Warning: Invalid length for PmTimerBlock: 0, using default 32 (20090903/tbfadt-607)
[    0.000000] ACPI: DSDT 0000003002a09ac0 00024 (v02    SGI  DSDTSN2 00020001    ? 00000001)
[    0.000000] ACPI: FACS 0000003002a09a70 00040
[    0.000000] ACPI: Local APIC address c0000000fee00000
[    0.000000] Number of logical nodes in system = 2
[    0.000000] Number of memory chunks in system = 2
[    0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] Initial ramdisk at: 0xe00000b079271000 (18311884 bytes)
[    0.000000] SAL 3.2: SGI SN2 version 4.53
[    0.000000] SAL Platform features: ITC_Drift
[    0.000000] SAL: AP wakeup using external interrupt vector 0x12
[    0.000000] ACPI: Local APIC address c0000000fee00000
[    0.000000] register_intr: No IOSAPIC for GSI 52
[    0.000000] 4 CPUs available, 4 CPUs total
[    0.000000] Increasing MCA rendezvous timeout from 20000 to 49000 milliseconds
[    0.000000] MCA related initialization done
[    0.000000] ACPI: RSDP 0000003002a09840 00024 (v02    SGI)
[    0.000000] ACPI: XSDT 0000003002a09880 00044 (v01    SGI  XSDTSN2 00010001    ? 00000001)
[    0.000000] ACPI: APIC 0000003002a098e0 0005C (v01    SGI  APICSN2 00010001    ? 00000001)
[    0.000000] ACPI: SRAT 0000003002a09950 000C0 (v01    SGI  SRATSN2 00010001    ? 00000001)
[    0.000000] ACPI: SLIT 0000003002a09a20 00030 (v01    SGI  SLITSN2 00010001    ? 00000001)
[    0.000000] ACPI: FACP 0000003002a09b00 000F4 (v03    SGI  FACPSN2 00030001    ? 00000001)
[    0.000000] ACPI Warning: 32/64X length mismatch in Pm1aEventBlock: 32/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: 32/64X length mismatch in Pm1aControlBlock: 16/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: 32/64X length mismatch in PmTimerBlock: 32/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: 32/64X length mismatch in Gpe0Block: 64/0 (20090903/tbfadt-526)
[    0.000000] ACPI Warning: Invalid length for Pm1aEventBlock: 0, using default 32 (20090903/tbfadt-607)
[    0.000000] ACPI Warning: Invalid length for Pm1aControlBlock: 0, using default 16 (20090903/tbfadt-607)
[    0.000000] ACPI Warning: Invalid length for PmTimerBlock: 0, using default 32 (20090903/tbfadt-607)
[    0.000000] ACPI: DSDT 0000003002a09ac0 00024 (v02    SGI  DSDTSN2 00020001    ? 00000001)
[    0.000000] ACPI: FACS 0000003002a09a70 00040
[    0.000000] SGI: Disabling VGA console
[    0.000000] SGI SAL version 4.53
[    0.000000] SAL_CAL_FLUSH failed with -1
[    0.000000] Virtual mem_map starts at 0xa0007fff65900000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00c00c00 -> 0x1000000000
[    0.000000]   Normal   0x1000000000 -> 0x1000000000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[5] active PFN ranges
[    0.000000]     0: 0x00c00c00 -> 0x00c1efff
[    0.000000]     1: 0x02c00c00 -> 0x02c1e9ff
[    0.000000]     1: 0x02c1ee00 -> 0x02c1ef59
[    0.000000]     1: 0x02c1ef68 -> 0x02c1ef84
[    0.000000]     1: 0x02c1efa0 -> 0x02c1efa4
[    0.000000] On node 0 totalpages: 123903
[    0.000000] free_area_init_node: node 0, pgdat e000003003120000, node_mem_map a0007fff8f92a000
[    0.000000]   DMA zone: 424 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 123479 pages, LIFO batch:7
[    0.000000] On node 1 totalpages: 122744
[    0.000000] free_area_init_node: node 1, pgdat e00000b003030080, node_mem_map a0007fffff92a000
[    0.000000]   DMA zone: 424 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 122320 pages, LIFO batch:7
[    0.000000] Built 2 zonelists in Node order, mobility grouping on.  Total pages: 245799
[    0.000000] Policy zone: DMA
[    0.000000] Kernel command line: BOOT_IMAGE=scsi0:/EFI/debian/vmlinuz root=UUID=74163b0c-1dde-4842-92a7-7496eb3b448b  ro
[    0.000000] PID hash table entries: 4096 (order: 1, 32768 bytes)
[    0.000000] Memory: 3901424k/3916208k available (7334k code, 44928k reserved, 3581k data, 736k init)
[    0.000000] SLUB: Genslabs=16, HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=256
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:1024
[    0.000000] CPU 0: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [ttySG0] enabled
[    0.020000] Calibrating delay loop... 2244.60 BogoMIPS (lpj=4489216)
[    0.120598] Security Framework initialized
[    0.121236] SELinux:  Disabled at boot.
[    0.122239] Dentry cache hash table entries: 524288 (order: 8, 4194304 bytes)
[    0.144109] Inode-cache hash table entries: 262144 (order: 7, 2097152 bytes)
[    0.150004] Mount-cache hash table entries: 1024
[    0.151243] Initializing cgroup subsys ns
[    0.152010] Initializing cgroup subsys cpuacct
[    0.152687] Initializing cgroup subsys devices
[    0.153557] Initializing cgroup subsys freezer
[    0.154439] Initializing cgroup subsys net_cls
[    0.208040] ACPI: Core revision 20090903
[    0.208806] Boot processor id 0x0/0x0
[    0.016000] Fixed BSP b0 value from CPU 1
[    0.016000] CPU 1: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz
[    0.016000] CPU 2: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz
[    0.016000] CPU 3: base freq=200.000MHz, ITC ratio=15/2, ITC freq=1500.000MHz
[    0.216072] Brought up 4 CPUs
[    0.252005] Total of 4 processors activated (8978.43 BogoMIPS).
[    0.253933] CPU0 attaching sched-domain:
[    0.253938]  domain 0: span 0-1 level CPU
[    0.253941]   groups: group a0000001009a4f70 cpus 0 group e000003003104f70 cpus 1
[    0.253949]   domain 1: span 0-3 level NODE
[    0.253952]    groups: group e00000307bd54000 cpus 0-1 (cpu_power = 2048) group e00000307bd54020 cpus 2-3 (cpu_power = 2048)
[    0.253964] CPU1 attaching sched-domain:
[    0.253967]  domain 0: span 0-1 level CPU
[    0.253970]   groups: group e000003003104f70 cpus 1 group a0000001009a4f70 cpus 0
[    0.253976]   domain 1: span 0-3 level NODE
[    0.253979]    groups: group e00000307bd54000 cpus 0-1 (cpu_power = 2048) group e00000307bd54020 cpus 2-3 (cpu_power = 2048)
[    0.253989] CPU2 attaching sched-domain:
[    0.253992]  domain 0: span 2-3 level CPU
[    0.253994]   groups: group e00000b003014f70 cpus 2 group e00000b003024f70 cpus 3
[    0.254001]   domain 1: span 0-3 level NODE
[    0.254004]    groups: group e00000b079263fe0 cpus 2-3 (cpu_power = 2048) group e00000b079263fc0 cpus 0-1 (cpu_power = 2048)
[    0.254015] CPU3 attaching sched-domain:
[    0.254017]  domain 0: span 2-3 level CPU
[    0.254020]   groups: group e00000b003024f70 cpus 3 group e00000b003014f70 cpus 2
[    0.254027]   domain 1: span 0-3 level NODE
[    0.254030]    groups: group e00000b079263fe0 cpus 2-3 (cpu_power = 2048) group e00000b079263fc0 cpus 0-1 (cpu_power = 2048)
[    0.256922] devtmpfs: initialized
[    0.270502] DMI not present or invalid.
[    0.292326] regulator: core version 0.5
[    0.292996] NET: Registered protocol family 16
[    0.336132] ACPI: bus type pci registered
[    0.337008] ACPI  DSDT OEM Rev 0x20001
[    0.340262] pci 0001:00:01.0: reg 10 32bit mmio: [0x200000-0x2fffff]
[    0.340940] pci 0001:00:03.0: reg 10 io port: [0x1000-0x10ff]
[    0.340983] pci 0001:00:03.0: reg 14 32bit mmio: [0x300000-0x300fff]
[    0.341178] pci 0001:00:03.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[    0.342067] pci 0001:00:04.0: reg 10 64bit mmio: [0x310000-0x31ffff]
[    0.342622] pci 0001:00:04.0: PME# supported from D3hot
[    0.376023] pci 0001:00:04.0: PME# disabled
[    0.377706] pci 0003:00:01.0: reg 10 io port: [0x1000-0x10ff]
[    0.377781] pci 0003:00:01.0: reg 14 64bit mmio: [0x200000-0x200fff]
[    0.377927] pci 0003:00:01.0: reg 30 32bit mmio pref: [0x220000-0x23ffff]
[    0.379151] pci 0005:00:01.0: reg 10 64bit mmio: [0x200000-0x20ffff]
[    0.379708] pci 0005:00:01.0: PME# supported from D3hot D3cold
[    0.412023] pci 0005:00:01.0: PME# disabled
[    0.413564] pci 0005:00:01.1: reg 10 64bit mmio: [0x210000-0x21ffff]
[    0.414121] pci 0005:00:01.1: PME# supported from D3hot D3cold
[    0.436022] pci 0005:00:01.1: PME# disabled
[    0.437656] pci 0006:00:02.0: reg 10 io port: [0x1000-0x10ff]
[    0.437737] pci 0006:00:02.0: reg 14 64bit mmio: [0x200000-0x200fff]
[    0.437895] pci 0006:00:02.0: reg 30 32bit mmio pref: [0x220000-0x23ffff]
[    0.444473] bio: create slab <bio-0> at 0
[    0.446016] ACPI: SCI (ACPI GSI 52) not registered
[    0.460009] ACPI: EC: Look up EC in DSDT
[    0.460118] ACPI: Interpreter enabled
[    0.460796] ACPI: (supports S0)
[    0.488240] ACPI: Using IOSAPIC for interrupt routing
[    0.489303] ACPI: No dock devices found.
[    0.492050] vgaarb: loaded
[    0.492759] Switching to clocksource sn2_rtc
[    0.540534] pnp: PnP ACPI init
[    0.541140] ACPI: bus type pnp registered
[    0.569138] pnp: PnP ACPI: found 0 devices
[    0.569978] ACPI: ACPI bus type pnp unregistered
[    0.571173] NET: Registered protocol family 2
[    0.571992] IP route cache hash table entries: 131072 (order: 6, 1048576 bytes)
[    0.629040] TCP established hash table entries: 524288 (order: 9, 8388608 bytes)
[    0.660317] TCP bind hash table entries: 65536 (order: 6, 1048576 bytes)
[    0.666056] TCP: Hash tables configured (established 524288 bind 65536)
[    0.675588] TCP reno registered
[    0.676514] NET: Registered protocol family 1
[    0.677443] Unpacking initramfs...
[    1.350027] Freeing initrd memory: 17856kB freed
[    1.351346] perfmon: version 2.0 IRQ 238
[    1.352019] perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits)
[    1.358843] perfmon: added sampling format default_format
[    1.371294] perfmon_default_smpl: default_format v2.0 registered
[    1.538984] audit: initializing netlink socket (disabled)
[    1.539935] type=2000 audit(1321307669.539:1): initialized
[    1.544061] HugeTLB registered 256 MB page size, pre-allocated 0 pages
[    1.555705] VFS: Disk quotas dquot_6.5.2
[    1.556597] Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
[    1.561104] msgmni has been set to 7654
[    1.562310] alg: No test for stdrng (krng)
[    1.572967] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.574259] io scheduler noop registered
[    1.574950] io scheduler anticipatory registered
[    1.575834] io scheduler deadline registered
[    1.604159] io scheduler cfq registered (default)
[    1.605288] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.624207] ACPI: Power Button [PWRF]
[    1.624959] input: Sleep Button as /devices/LNXSYSTM:00/LNXSLPBN:00/input/input1
[    1.626227] ACPI: Sleep Button [SLPF]
[    1.660223] IRQ 233/system controller events: IRQF_DISABLED is not guaranteed on shared IRQs
[    1.661760] Linux agpgart interface v0.103
[    1.662607] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.678687] sn_console: Console driver init
[    1.679376] ttySG0 at I/O 0x0 (irq = 0) is a SGI SN L1
[    1.684414] IRQ 233/SAL console driver: IRQF_DISABLED is not guaranteed on shared IRQs
[    1.696995] mice: PS/2 mouse device common for all mice
[    1.697947] rtc-efi rtc-efi: rtc core: registered rtc-efi as rtc0
[    1.706044] TCP cubic registered
[    1.706597] NET: Registered protocol family 17
[    1.719520] registered taskstats version 1
[    1.722534] rtc-efi rtc-efi: setting system clock to 2011-11-14 21:54:29 UTC (1321307669)
[    1.750664] Freeing unused kernel memory: 736kB freed
[    1.773561] udev[73]: starting version 164
[    1.826773] SCSI subsystem initialized
[    1.827687] IOC4 0001:00:01.0: can't derive routing for PCI INT A
[    1.831026] IOC4 0001:00:01.0: PCI INT A: no GSI
[    1.831934] IOC4 0001:00:01.0: IO9 card detected.
[    1.884874] QLogic Fibre Channel HBA Driver: 8.03.01-k6
[    2.090420] IOC4 0001:00:01.0: PCI clock is 15 ns.
[    2.090494] qla2xxx 0003:00:01.0: can't derive routing for PCI INT A
[    2.091542] qla2xxx 0003:00:01.0: PCI INT A: no GSI
[    2.092452] qla2xxx 0003:00:01.0: Found an ISP2300, irq 60, iobase 0xc00000080f400000
[    2.094057] IOC4 loading sgiioc4 submodule
[    2.118806] tg3.c:v3.116 (December 3, 2010)
[    2.119708] tg3 0001:00:04.0: can't derive routing for PCI INT A
[    2.128902] tg3 0001:00:04.0: PCI INT A: no GSI
[    2.130262] qla2xxx 0003:00:01.0: Configuring PCI space...
[    2.136168] Uniform Multi-Platform E-IDE driver
[    2.137663] SGIIOC4: IDE controller at PCI slot 0001:00:01.0, revision 83
[    2.137681]     ide0: MMIO-DMA
[    2.137694] Probing IDE interface ide0...
[    2.153389] qla2xxx 0003:00:01.0: Configure NVRAM parameters...
[    2.305234] qla2xxx 0003:00:01.0: Verifying loaded RISC code...
[    2.319523] qla2xxx 0003:00:01.0: firmware: requesting ql2300_fw.bin
[    2.419551] qla2xxx 0003:00:01.0: Allocated (412 KB) for firmware dump...
[    2.563580] scsi0 : qla2xxx
[    2.564575] qla2xxx 0003:00:01.0:
[    2.564576]  QLogic Fibre Channel HBA Driver: 8.03.01-k6
[    2.564578]   QLogic QLA2310 -
[    2.564579]   ISP2300: PCI-X (66 MHz) @ 0003:00:01.0 hdma+, host#=0, fw=3.03.27 IPX
[    2.572066] qla2xxx 0006:00:02.0: can't derive routing for PCI INT A
[    2.597290] qla2xxx 0006:00:02.0: PCI INT A: no GSI
[    2.598211] qla2xxx 0006:00:02.0: Found an ISP2300, irq 61, iobase 0xc00000080de00000
[    2.600496] qla2xxx 0006:00:02.0: Configuring PCI space...
[    2.628129] qla2xxx 0006:00:02.0: Configure NVRAM parameters...
[    2.764567] qla2xxx 0006:00:02.0: Verifying loaded RISC code...
[    2.875545] qla2xxx 0006:00:02.0: Allocated (412 KB) for firmware dump...
[    2.880394] hda: MATSHITADVD-ROM SR-8589, ATAPI CD/DVD-ROM drive
[    3.019596] scsi1 : qla2xxx
[    3.020527] qla2xxx 0006:00:02.0:
[    3.020528]  QLogic Fibre Channel HBA Driver: 8.03.01-k6
[    3.020530]   QLogic QLA2310 -
[    3.020531]   ISP2300: PCI-X (66 MHz) @ 0006:00:02.0 hdma+, host#=1, fw=3.03.27 IPX
[    3.215975] hda: MWDMA2 mode selected
[    3.217735] ide0 at 0xc00000080c200100-0xc00000080c20011c,0xc00000080c200120 on irq 64
[    3.232197] ide-cd driver 5.00
[    3.233572] ide-cd: hda: ATAPI 48X DVD-ROM drive, 256kB Cache
[    3.237187] Uniform CD-ROM driver Revision: 3.20
[    3.836329] tg3 0001:00:04.0: eth0: Tigon3 [partno(030-1771-000) rev 0105] (PCI:66MHz:64-bit) MAC address 08:00:69:13:f6:0d
[    3.838181] tg3 0001:00:04.0: eth0: attached PHY is 5701 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[    3.839722] tg3 0001:00:04.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[0]
[    3.861918] tg3 0001:00:04.0: eth0: dma_rwctrl[76ff3f0f] dma_mask[64-bit]
[    3.863218] qla1280: QLA12160 found on PCI bus 0, dev 3
[    3.864100] qla1280 0001:00:03.0: can't derive routing for PCI INT A
[    3.879024] qla1280 0001:00:03.0: PCI INT A: no GSI
[    3.880007] tg3 0005:00:01.0: can't derive routing for PCI INT A
[    3.897124] tg3 0005:00:01.0: PCI INT A: no GSI
[    3.899216] scsi(2): Enabling SN2 PCI DMA dual channel lockup workaround
[    3.910588] qla1280 0001:00:03.0: firmware: requesting qlogic/12160.bin
[    3.933079] tg3 0005:00:01.0: eth1: Tigon3 [partno(030-2126-001) rev 2100] (PCI:66MHz:64-bit) MAC address 00:e0:ed:07:ce:a0
[    3.934971] tg3 0005:00:01.0: eth1: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[    3.936527] tg3 0005:00:01.0: eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    3.960059] tg3 0005:00:01.0: eth1: dma_rwctrl[763f0000] dma_mask[64-bit]
[    3.961541] tg3 0005:00:01.1: can't derive routing for PCI INT B
[    3.977372] tg3 0005:00:01.1: PCI INT B: no GSI
[    4.002800] scsi(2): Enabling SN2 PCI DMA workaround
[    4.004170] tg3 0005:00:01.1: eth2: Tigon3 [partno(030-2126-001) rev 2100] (PCI:66MHz:64-bit) MAC address 00:e0:ed:07:ce:a1
[    4.009823] tg3 0005:00:01.1: eth2: attached PHY is 5704 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[    4.011552] tg3 0005:00:01.1: eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[    4.035150] tg3 0005:00:01.1: eth2: dma_rwctrl[763f0000] dma_mask[64-bit]
[    4.045696] scsi(2:0): Resetting SCSI BUS
[    8.182586] qla2xxx 0006:00:02.0: LOOP UP detected (2 Gbps).
[    9.047062] scsi 1:0:0:0: Direct-Access     DGC      LUNZ             0326 PQ: 0 ANSI: 4
[    9.051407] scsi(2:1): Resetting SCSI BUS
[    9.054416] scsi 1:0:1:0: Direct-Access     DGC      LUNZ             0430 PQ: 0 ANSI: 4
[    9.057962] sd 1:0:0:0: [sda] READ CAPACITY failed
[    9.058811] sd 1:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[    9.071189] sd 1:0:0:0: [sda] Sense Key : Illegal Request [current]
[    9.072059] sd 1:0:1:0: [sdb] READ CAPACITY failed
[    9.072063] sd 1:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[    9.072068] sd 1:0:1:0: [sdb] Sense Key : Illegal Request [current]
[    9.072073] sd 1:0:1:0: [sdb] Add. Sense: Logical unit not supported
[    9.104576]
[    9.125657] sd 1:0:0:0: [sda]
[    9.126140] sd 1:0:1:0: [sdb] Test WP failed, assume Write Enabled
[    9.126160] Add. Sense: Logical unit not supported
[    9.126539] sd 1:0:0:0: [sda] Test WP failed, assume Write Enabled
[    9.126649] sd 1:0:0:0: [sda] Asking for cache data failed
[    9.126652] sd 1:0:0:0: [sda] Assuming drive cache: write through
[    9.127437] sd 1:0:0:0: [sda] READ CAPACITY failed
[    9.127440] sd 1:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[    9.127443] sd 1:0:0:0: [sda] Sense Key : Illegal Request [current]
[    9.127446] sd 1:0:0:0: [sda] Add. Sense: Logical unit not supported
[    9.127754] sd 1:0:0:0: [sda] Test WP failed, assume Write Enabled
[    9.127854] sd 1:0:0:0: [sda] Asking for cache data failed
[    9.127856] sd 1:0:0:0: [sda] Assuming drive cache: write through
[    9.127860] sd 1:0:0:0: [sda] Attached SCSI disk
[    9.242467] sd 1:0:1:0: [sdb] Asking for cache data failed
[    9.254202] sd 1:0:1:0: [sdb] Assuming drive cache: write through
[    9.256858] sd 1:0:1:0: [sdb] READ CAPACITY failed
[    9.257754] sd 1:0:1:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[    9.288177] sd 1:0:1:0: [sdb] Sense Key : Illegal Request [current]
[    9.289500] sd 1:0:1:0: [sdb] Add. Sense: Logical unit not supported
[    9.369996] sd 1:0:1:0: [sdb] Test WP failed, assume Write Enabled
[    9.394796] sd 1:0:1:0: [sdb] Asking for cache data failed
[    9.413700] sd 1:0:1:0: [sdb] Assuming drive cache: write through
[    9.414791] sd 1:0:1:0: [sdb] Attached SCSI disk
[   10.033047] scsi 1:0:2:0: Direct-Access     DGC      LUNZ             0430 PQ: 0 ANSI: 4
[   10.036877] sd 1:0:2:0: [sdc] READ CAPACITY failed
[   10.036890] scsi 1:0:3:0: Direct-Access     DGC      LUNZ             0326 PQ: 0 ANSI: 4
[   10.042887] sd 1:0:2:0: [sdc]
[   10.043116] scsi 1:0:4:0: Direct-Access     DGC      LUNZ             0326 PQ: 0 ANSI: 4
[   10.043505] sd 1:0:3:0: [sdd] READ CAPACITY failed
[   10.043507] sd 1:0:3:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.043510] sd 1:0:3:0: [sdd] Sense Key : Illegal Request [current]
[   10.043514] sd 1:0:3:0: [sdd] Add. Sense: Logical unit not supported
[   10.044093] sd 1:0:3:0: [sdd] Test WP failed, assume Write Enabled
[   10.044230] sd 1:0:3:0: [sdd] Asking for cache data failed
[   10.044233] sd 1:0:3:0: [sdd] Assuming drive cache: write through
[   10.045600] sd 1:0:3:0: [sdd] READ CAPACITY failed
[   10.045603] sd 1:0:3:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.045607] sd 1:0:3:0: [sdd] Sense Key : Illegal Request [current]
[   10.045610] sd 1:0:3:0: [sdd] Add. Sense: Logical unit not supported
[   10.046098] sd 1:0:3:0: [sdd] Test WP failed, assume Write Enabled
[   10.046261] sd 1:0:3:0: [sdd] Asking for cache data failed
[   10.046264] sd 1:0:3:0: [sdd] Assuming drive cache: write through
[   10.046268] sd 1:0:3:0: [sdd] Attached SCSI disk
[   10.047093] scsi 1:0:5:0: Direct-Access     DGC      LUNZ             0326 PQ: 0 ANSI: 4
[   10.048421] sd 1:0:4:0: [sde] READ CAPACITY failed
[   10.048426] sd 1:0:4:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.048432] sd 1:0:4:0: [sde] Sense Key : Illegal Request [current]
[   10.048436] sd 1:0:4:0: [sde] Add. Sense: Logical unit not supported
[   10.050149] sd 1:0:4:0: [sde] Test WP failed, assume Write Enabled
[   10.050318] sd 1:0:4:0: [sde] Asking for cache data failed
[   10.050321] sd 1:0:4:0: [sde] Assuming drive cache: write through
[   10.051478] sd 1:0:5:0: [sdf] READ CAPACITY failed
[   10.051481] sd 1:0:5:0: [sdf] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.051485] sd 1:0:5:0: [sdf] Sense Key : Illegal Request [current]
[   10.051488] sd 1:0:5:0: [sdf] Add. Sense: Logical unit not supported
[   10.051566] sd 1:0:4:0: [sde] READ CAPACITY failed
[   10.051569] sd 1:0:4:0: [sde] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.051572] sd 1:0:4:0: [sde] Sense Key : Illegal Request [current]
[   10.051576] sd 1:0:4:0: [sde] Add. Sense: Logical unit not supported
[   10.051972] sd 1:0:5:0: [sdf] Test WP failed, assume Write Enabled
[   10.051991] sd 1:0:4:0: [sde] Test WP failed, assume Write Enabled
[   10.052125] sd 1:0:5:0: [sdf] Asking for cache data failed
[   10.052128] sd 1:0:5:0: [sdf] Assuming drive cache: write through
[   10.052138] sd 1:0:4:0: [sde] Asking for cache data failed
[   10.052140] sd 1:0:4:0: [sde] Assuming drive cache: write through
[   10.052144] sd 1:0:4:0: [sde] Attached SCSI disk
[   10.053019] sd 1:0:5:0: [sdf] READ CAPACITY failed
[   10.053021] sd 1:0:5:0: [sdf] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.053025] sd 1:0:5:0: [sdf] Sense Key : Illegal Request [current]
[   10.053029] sd 1:0:5:0: [sdf] Add. Sense: Logical unit not supported
[   10.053446] sd 1:0:5:0: [sdf] Test WP failed, assume Write Enabled
[   10.053577] sd 1:0:5:0: [sdf] Asking for cache data failed
[   10.053580] sd 1:0:5:0: [sdf] Assuming drive cache: write through
[   10.053584] sd 1:0:5:0: [sdf] Attached SCSI disk
[   10.700538] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.736190] sd 1:0:2:0: [sdc] Sense Key : Illegal Request [current]
[   10.753568] sd 1:0:2:0: [sdc] Add. Sense: Logical unit not supported
[   10.755314] sd 1:0:2:0: [sdc] Test WP failed, assume Write Enabled
[   10.807453] sd 1:0:2:0: [sdc] Asking for cache data failed
[   10.821007] sd 1:0:2:0: [sdc] Assuming drive cache: write through
[   10.823019] sd 1:0:2:0: [sdc] READ CAPACITY failed
[   10.823948] sd 1:0:2:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[   10.870762] sd 1:0:2:0: [sdc] Sense Key : Illegal Request [current]
[   10.872073] sd 1:0:2:0: [sdc] Add. Sense: Logical unit not supported
[   10.947612] sd 1:0:2:0: [sdc] Test WP failed, assume Write Enabled
[   10.974438] sd 1:0:2:0: [sdc] Asking for cache data failed
[   10.975424] sd 1:0:2:0: [sdc] Assuming drive cache: write through
[   10.976524] sd 1:0:2:0: [sdc] Attached SCSI disk
[   14.059407] scsi2 : QLogic QLA12160 PCI to SCSI Host Adapter
[   14.059408]        Firmware version: 10.04.42, Driver version 3.27
[   14.153841] md: linear personality registered for level -1
[   14.158282] md: multipath personality registered for level -4
[   14.167057] md: raid0 personality registered for level 0
[   14.179127] md: raid1 personality registered for level 1
[   14.251417] raid6: int64x1   1247 MB/s
[   14.313459] scsi 2:0:1:0: Direct-Access     SGI      ST373307LC       2743 PQ: 0 ANSI: 3
[   14.315354] scsi(2:0:1:0): Sync: period 9, offset 14, Wide, DTraid6: int64x2   1986 MB/s
[   14.318915] , Tagged queuing: depth 31
[   14.387423] raid6: int64x4   2231 MB/s
[   14.455405] raid6: int64x8   2831 MB/s
[   14.523403] raid6: int64x16  3216 MB/s
[   14.591410] raid6: int64x32  2207 MB/s
[   14.592094] raid6: using algorithm int64x16 (3216 MB/s)
[   14.594375] xor: measuring software checksum speed
[   14.611398]    ia64      :  3112.000 MB/sec
[   14.612163] xor: using function: ia64 (3112.000 MB/sec)
[   14.619263] md: raid6 personality registered for level 6
[   14.625819] md: raid5 personality registered for level 5
[   14.626705] md: raid4 personality registered for level 4
[   14.635954] md: raid10 personality registered for level 10
[   21.335434] sd 2:0:1:0: [sdg] 143374744 512-byte logical blocks: (73.4 GB/68.3 GiB)
[   21.338354] sd 2:0:1:0: [sdg] Write Protect is off
[   21.339165] sd 2:0:1:0: [sdg] Mode Sense: ab 00 10 08
[   21.340665] sd 2:0:1:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA
[   21.348302]  sdg: sdg1 sdg2 sdg3
[   21.380663] sd 2:0:1:0: [sdg] Attached SCSI disk
[   21.729769] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[   21.733455] SGI XFS Quota Management subsystem
[   21.756846] XFS mounting filesystem sdg3
[   21.904505] Ending clean XFS mount for filesystem: sdg3
[   23.397332] udev[364]: starting version 164
[   25.679991] qla2xxx 0003:00:01.0: Cable is unplugged...
[   27.224656] Adding 2104480k swap on /dev/sdg2.  Priority:-1 extents:1 across:2104480k
[   28.874043] loop: module loaded
[   30.371430] NET: Registered protocol family 10
[   30.856671] fuse init (API version 7.13)
[   31.491567] RPC: Registered udp transport module.
[   31.492424] RPC: Registered tcp transport module.
[   31.493305] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   31.806940] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   32.008494] svc: failed to register lockdv1 RPC service (errno 97).
[   32.011347] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   32.096803] NFSD: starting 90-second grace period
[   35.052197] NetworkManager(1364): unaligned access to 0x600000000002621c, ip=0x20000000007d1a70
[   35.053742] NetworkManager(1364): unaligned access to 0x6000000000026224, ip=0x20000000007d1aa0
[   35.055305] NetworkManager(1364): unaligned access to 0x600000000002622c, ip=0x20000000007d1ac0
[   35.074548] NetworkManager(1364): unaligned access to 0x600000000002621c, ip=0x20000000007d1a70
[   35.082309] NetworkManager(1364): unaligned access to 0x6000000000026224, ip=0x20000000007d1aa0
[   36.109526] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   36.127598] tg3 0005:00:01.0: firmware: requesting tigon/tg3_tso.bin
[   36.341303] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   36.345431] tg3 0005:00:01.1: firmware: requesting tigon/tg3_tso.bin
[   36.439280] ADDRCONF(NETDEV_UP): eth2: link is not ready
[   38.987456] tg3 0001:00:04.0: eth0: Link is up at 1000 Mbps, full duplex
[   38.988532] tg3 0001:00:04.0: eth0: Flow control is on for TX and on for RX
[   38.993915] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   40.243057] Bluetooth: Core ver 2.15
[   40.244026] NET: Registered protocol family 31
[   40.244711] Bluetooth: HCI device and connection manager initialized
[   40.250151] Bluetooth: HCI socket layer initialized
[   40.437716] Bluetooth: L2CAP ver 2.14
[   40.438364] Bluetooth: L2CAP socket layer initialized
[   40.457345] Bluetooth: RFCOMM TTY layer initialized
[   40.458108] Bluetooth: RFCOMM socket layer initialized
[   40.459190] Bluetooth: RFCOMM ver 1.11
[   40.647127] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   40.648007] Bluetooth: BNEP filters: protocol multicast
[   40.672715] Bridge firewalling registered
[   40.675168] NetworkManager(1364): unaligned access to 0x600000000004a95c, ip=0x20000000007d1a70
[   40.678591] NetworkManager(1364): unaligned access to 0x600000000004a964, ip=0x20000000007d1aa0
[   40.680151] NetworkManager(1364): unaligned access to 0x600000000004a96c, ip=0x20000000007d1ac0
[   40.758959] Bluetooth: SCO (Voice Link) ver 0.6
[   40.759809] Bluetooth: SCO socket layer initialized
[   41.424796] lp: driver loaded but no devices found
[   41.524524] ppdev: user-space parallel port driver
[   49.583398] eth0: no IPv6 routers present
[   79.319436] NetworkManager(1364): unaligned access to 0x600000000002ed1c, ip=0x20000000007d1a70
[   79.320923] NetworkManager(1364): unaligned access to 0x600000000002ed24, ip=0x20000000007d1aa0
[   79.322462] NetworkManager(1364): unaligned access to 0x600000000002ed2c, ip=0x20000000007d1ac0
[   80.352703] NetworkManager(1364): unaligned access to 0x600000000002ed1c, ip=0x20000000007d1a70
[   80.354243] NetworkManager(1364): unaligned access to 0x600000000002ed24, ip=0x20000000007d1aa0
[  680.561123] lp: driver loaded but no devices found
[  680.585002] ide-gd driver 1.18
[  680.617372] st: Version 20081215, fixed bufsize 32768, s/g segs 256
[  680.656093] sd 1:0:0:0: Attached scsi generic sg0 type 0
[  680.657320] sd 1:0:1:0: Attached scsi generic sg1 type 0
[  680.658409] sd 1:0:2:0: Attached scsi generic sg2 type 0
[  680.663905] sd 1:0:3:0: Attached scsi generic sg3 type 0
[  680.665031] sd 1:0:4:0: Attached scsi generic sg4 type 0
[  680.677819] sd 1:0:5:0: Attached scsi generic sg5 type 0
[  680.689862] sd 2:0:1:0: Attached scsi generic sg6 type 0
roan:~#


This is Debian 6 'squeeze' for which, as far as I know, there is no hinv command available, ProPack or otherwise.

Pics coming; it's sharing its cabinet with a 13 node Altix 350 system (has a router, 26 CPU's and 46GB of RAM) which I'll post the info about tomorrow. There is another altix 3700 in the lot, but no power to its location yet; it's a 20 CPU 20GB smallish config (5 C-bricks, 4 R-bricks, one IX-brick).

Big thanks to Voralyan for the posts in the Altix 350 Debian thread; the Altix 3700 is virtually the same beast as far as Debian is concerned.


Top
 Profile  
 
Unread postPosted: Sat Nov 19, 2011 5:17 pm 
Offline
User avatar

Joined: Sat Oct 15, 2011 4:53 pm
Posts: 11
And pics....

Attachment:
File comment: Minimum Altix 3700 configuration, in bottom of Altix 3000 rack, with a larger Altix 350 system above.
100_6135.JPG
100_6135.JPG [ 3.18 MiB | Viewed 605 times ]

Attachment:
File comment: Rear view.
100_6136.JPG
100_6136.JPG [ 2.7 MiB | Viewed 605 times ]


Top
 Profile  
 
Unread postPosted: Thu Dec 01, 2011 8:30 am 
Offline

Joined: Mon Jan 04, 2010 3:58 pm
Posts: 115
Location: New York - But Not That New York
I'd going to ask you a question that is probably dumb to the point of nearly suicidal. We have a similar setup here, a small Altix 3700 (in our case in its own "short" rack, 12 CPU setup) and a 350 (in a "tall" rack, 16 CPU setup). Have you ever tried to numalink them together to run as a single system?

I seem to recall reading that the Altix does not have to be made of all the same speed/generation CPUs, as long as each node is homogeneous within itself. The link cables seem to be the same as well, but of course that doesn't necessarily mean much.

_________________
Currently, in ascending order of (my) time consumption -
:Fuel: :Fuel: :Fuel: :Fuel: :Octane: :Octane: :O2: :Octane2: :AltixDS: :A350R:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group