Nekochan Net

Official Chat Channel: #nekochan // irc.nekochan.net
It is currently Fri Oct 31, 2014 5:52 am

All times are UTC - 8 hours [ DST ]


Forum rules


Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.



Post new topic Reply to topic  [ 13 posts ] 
Author Message
Unread postPosted: Sat Feb 09, 2008 9:32 am 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
Code:
mark@PerfectChaos ~ $ hinv -vm
Location: /hw/node
            PM20 Board: barcode ENE950     part 030-0890-003 rev  G
Location: /hw/node/xtalk/15
            IP30 Board: barcode EAX320     part 030-0887-005 rev  B
Location: /hw/node/xtalk/15/pci/2
             FP1 Board: barcode DKN962     part 030-0891-003 rev  A
    PWR.SPPLY.SR Board: barcode AAA7170133 part 060-0028-003 rev  A
Location: /hw/node/xtalk/12
            GM20 Board: barcode DZD138     part 030-0957-003 rev  N
2 195 MHZ IP30 Processors
Heart ASIC: Revision D
CPU: MIPS R10000 Processor Chip Revision: 2.7
FPU: MIPS R10010 Floating Point Chip Revision: 0.0
Main memory size: 1024 Mbytes
Xbow ASIC: Revision 1.2
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 1 Mbyte
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
  CDROM: unit 4 on SCSI controller 1
IOC3 serial port: tty1
IOC3 serial port: tty2
IOC3 parallel port: plp1
Graphics board: MXI
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 4265, device 3) pci slot 2
  PCI Adapter ID (vendor 4215, device 4128) pci slot 0
  PCI Adapter ID (vendor 4215, device 4128) pci slot 1
  PCI Adapter ID (vendor 4265, device 5) pci slot 3
mark@PerfectChaos ~ $ /usr/gfx/gfxinfo
Graphics board 0 is "IMPACTSR" graphics.
        Managed (":0.0") 1280x1024
        Product ID 0x3, 2 GEs, 2 REs, 4 TRAMs
        MGRAS revision 2, RA revision 0
        HQ rev B, GE11 rev B, RE4 rev C, PP1 rev A,
        VC3 rev A, CMAP rev E, Heart rev D
        19" monitor (id 0x1)

        Channel 0:
         Origin = (0,0)
         Video Output: 1280 pixels, 1024 lines, 72.24Hz (1280x1024_72)


I also have a granite keyboard & mouse and a gdm-20d11 granite monitor, and octane speakers (which kinda really suck) hooked up to this system.

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Last edited by guardian452 on Fri Aug 21, 2009 12:45 pm, edited 2 times in total.

Top
 Profile  
 
Unread postPosted: Fri Aug 21, 2009 12:44 pm 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
upgraded graphics and new irix install:


Code:
chaos 18# hinv -vm
Location: /hw/node
            PM20 Board: barcode ENE950     part 030-0890-003 rev  G
Location: /hw/node/xtalk/15
            IP30 Board: barcode EAX320     part 030-0887-005 rev  B
Location: /hw/node/xtalk/15/pci/2
             FP1 Board: barcode DKN962     part 030-0891-003 rev  A
    PWR.SPPLY.SR Board: barcode AAA7170133 part 060-0028-003 rev  A
Location: /hw/node/xtalk/11
           ODY32 Board: barcode KWC425     part 030-1403-003 rev  A
2 195 MHZ IP30 Processors
Heart ASIC: Revision D
CPU: MIPS R10000 Processor Chip Revision: 2.7
FPU: MIPS R10010 Floating Point Chip Revision: 0.0
Main memory size: 1024 Mbytes
Xbow ASIC: Revision 1.2
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 1 Mbyte
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
  CDROM: unit 4 on SCSI controller 1
IOC3 serial port: tty1
IOC3 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V6
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 4265, device 3) pci slot 2
  PCI Adapter ID (vendor 4215, device 4128) pci slot 0
  PCI Adapter ID (vendor 4215, device 4128) pci slot 1
  PCI Adapter ID (vendor 4265, device 5) pci slot 3
chaos 19# /usr/gfx/gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 1280x1024
        BUZZ version A.1
        PB&J version 1
        32MB memory
                Banks: 2, CAS latency: 3
         Monitor 0 type: Unknown
        Channel 0:
         Origin = (0,0)
         Video Output: 1280 pixels, 1024 lines, 60.00Hz (1280x1024_60)

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Top
 Profile  
 
Unread postPosted: Fri Aug 21, 2009 12:49 pm 
Offline
User avatar

Joined: Tue Jun 17, 2008 8:38 pm
Posts: 439
Location: Socal
Sweet! Hope you're enjoying it. Do you notice a difference in speed between MXI and V6?

_________________
:Onyx2: :Fuel: :Indigo2: :Indigo2IMP: :O3x0:


Top
 Profile  
 
Unread postPosted: Fri Aug 21, 2009 2:16 pm 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
bigD wrote:
Sweet! Hope you're enjoying it. Do you notice a difference in speed between MXI and V6?


I haven't noticed much of a difference, but haven't been able to do much with it yet as I'm still getting the OS sorted out. Some 3d demos I tried seem much smoother than before; the big reason for the upgrade was so textured objects (especially games and videos) wouldn't have a scanlined appearance due to faulty tram.

also I think the power consumption is (maybe?) a bit lower.

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Top
 Profile  
 
Unread postPosted: Sat Aug 22, 2009 12:32 am 
Offline
User avatar

Joined: Wed Aug 20, 2008 5:38 am
Posts: 916
Location: North of England
sybrfreq wrote:
I also have a granite keyboard & mouse and a gdm-20d11 granite monitor, and octane speakers (which kinda really suck) hooked up to this system.

Soon I will have a pair of Gigaworks T20 Series IIs hooked up to mine.

_________________
:Indy: R4600PC 133 MHz

Mac Mini 2.5GHz 8GB RAM
Raspberry Pi
Dell XPS M1530


Top
 Profile  
 
Unread postPosted: Mon Oct 19, 2009 5:40 pm 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
bigD wrote:
Sweet! Hope you're enjoying it. Do you notice a difference in speed between MXI and V6?


oh yeah, it's sweeter, badder, and just plain faster all around. (now that I've had a few months to wear it in ;) ) But a big reason for upgrading was to get rid of the MXI scanlines in textured windows, especially mplayer videos. Should have gone with a v8 though, the low color depth (I believe that is causing the dithering??) is a bit noticable for some things. In places I wouldn't expect to notice it, like fast-paced games such as quake2 and bzflag.

Now I need a faster pair of processors. Boy do I <3 my octane. All the other computers can go pound sand, I love my octane. :)


indyman007 wrote:
Soon I will have a pair of Gigaworks T20 Series IIs hooked up to mine.
Well, if you must know, there is currently a pair of Mackie SRM450s just a rockin' but that is only a temporary setup. Normally I use a shure psm200 in-ear but sometimes you need to let a friend listen, and the octane speakers are perfectly adequate for getting a tune across.

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Top
 Profile  
 
Unread postPosted: Tue Dec 14, 2010 11:29 am 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
Some more upgrades... CPU, RAM, and Power Supply. I'm lovin' it!

Irix is currently 6.5.29

Code:
Chaos 1% hinv -mv
Location: /hw/node
      PM10400MHZ Board: barcode LJX779     part 030-1475-001 rev  B
Location: /hw/node/xtalk/15
            IP30 Board: barcode EAX320     part 030-0887-005 rev  B
Location: /hw/node/xtalk/15/pci/2
             FP1 Board: barcode KFG129     part 030-0891-003 rev  G
    PWR.SPPLY.ER Board: barcode AAE8420185 part 060-0035-001 rev  B
Location: /hw/node/xtalk/11
           ODY32 Board: barcode KWC425     part 030-1403-003 rev  A
1 400 MHZ IP30 Processor
Heart ASIC: Revision D
CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
Main memory size: 2048 Mbytes
Xbow ASIC: Revision 1.4
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 2 Mbytes
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  Tape drive: unit 3 on SCSI controller 0: DAT
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V6
Integral Fast Ethernet: ef0, version 1, pci 2
Iris Audio Processor: version RAD revision 12.0, number 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
Chaos 2% /usr/gfx/gfxinfo
Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 1280x1024
        BUZZ version A.1
        PB&J version 1
        32MB memory
                Banks: 2, CAS latency: 3
         Monitor 0 type: Unknown
        Channel 0:
         Origin = (0,0)
         Video Output: 1280 pixels, 1024 lines, 59.00Hz (1280x1024_59)


Since it is the trend nowadays here is a few pictures... I just moved yesterday but had these extra octane parts and figured I'd better put them in before they are lost or damaged :mrgreen:

I would like to say that my workspace is typically neater than this but... :P I do intend to move the family tree poster at some point.


Attachments:
DSC03252_768.jpg
DSC03252_768.jpg [ 295.24 KiB | Viewed 1336 times ]
DSC03253_768.jpg
DSC03253_768.jpg [ 291.5 KiB | Viewed 1336 times ]

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Last edited by guardian452 on Tue Dec 14, 2010 11:55 am, edited 1 time in total.
Top
 Profile  
 
Unread postPosted: Tue Dec 14, 2010 11:36 am 
Offline
User avatar

Joined: Mon Nov 12, 2007 8:54 pm
Posts: 1321
Location: Berkeley, CA, USA, NA, Earth, Sol
2009 wrote:
Xbow ASIC: Revision 1.2

2010 wrote:
Xbow ASIC: Revision 1.4

Numerous upgrades...

_________________
Then? :IRIS3130: ... Now? :O3x02L: :A3504L:- :A3502L: :1600SW:+MLA :Fuel: :Octane2: :Octane: :Indigo2IMP: ... Other: DEC :BA213: :BA123: Sun, DG AViiON, NeXT :Cube:


Top
 Profile  
 
Unread postPosted: Tue Dec 14, 2010 11:38 am 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
I actually upgraded that last November, because my old frontplane died... I cleaned it for what looked like the first time in it's 12 years and I guess it needed all that dust to function properly. I never bothered to post a new hinv because... well, it's just a frontplane. ;)

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Top
 Profile  
 
Unread postPosted: Fri Dec 17, 2010 1:44 pm 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
viewtopic.php?f=3&t=16724537&p=7333522#p7333522

v6 with 1.2 xbow... that must be me... just so there's no confusion, v6/v8 will work with any xbow, but v10/v12 needs 1.4.

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Top
 Profile  
 
Unread postPosted: Tue Dec 06, 2011 5:16 pm 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
R.I.P. Chaos 1997-2011 ... about two inches of water in the basement last night :oops: and guess who was sitting on the floor

I had a lot of fun with it, but don't be sad because it was heading for a dumpster when I got it.

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Top
 Profile  
 
Unread postPosted: Tue Dec 06, 2011 5:43 pm 
Offline
User avatar

Joined: Fri Sep 25, 2009 10:40 am
Posts: 158
Location: Albany, OR USA
Was it running at the time? If it was (totally) powered off, it would probably still run after a thorough drying out. If it was plugged in but powered off, most of the system may still be OK, except the power supply.

_________________
:Onyx2: 4x400MHz R12K Onyx2 IR2, 5GB RAM
:1600SW: :Indigo2IMP: R10K Indigo2 MaxIMPACT, 4 TRAMS, 768MB RAM, 2x9GB HD, CD-ROM, Phobos G160
Black Cardinal


Top
 Profile  
 
Unread postPosted: Sat Dec 10, 2011 10:48 am 
Offline
User avatar

Joined: Tue Aug 21, 2007 10:12 pm
Posts: 2859
Location: Fantasyland
It might be salvageable, I was finally able to pull out the power supply finally by prying it out with a big screwdriver (it's an octane2 psu, but doesn't have a handle). Something sticky had glued it in. Other than that it seems to be fine, no rust yet and it is really clean ;) , I haven't gotten around to powering it up yet. It was totally unplugged. I don't think the water came up to the mainboard/frontplane. Just the bottom half inch or so.

It's one of the few things from my music room that I left downstairs during the remodel because it was so heavy I didn't want to put it in storage. I had my TV, VCR, and DTV tuner also on the floor... My TV is fine but the VCR was trashed. It was really dirty water and it would have got in the bearings and washed away lubricants. I have an SVHS unit to replace it that can do 'perfect pause', variable speed slomo and frame by frame with a big knob on the remote, perfect for what I use a VCR for. Most DVDs and digital boxes are too encumbered with copy protection, complex menus, etc. I like VHS machines, so long as I can find tapes for them.

_________________
"If no one comes from the future to stop you from doing it then how bad of a decision can it really be?"


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 13 posts ] 

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group