O2+ 400MHz R12K, 1GB RAM, DVD, 1600SW, 2Gbit FC, blue skins

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
User avatar
jan-jaap
Posts: 4065
Joined: Thu Jun 17, 2004 11:35 am
Location: Wijchen, The Netherlands

O2+ 400MHz R12K, 1GB RAM, DVD, 1600SW, 2Gbit FC, blue skins

Unread postby jan-jaap » Tue Dec 14, 2010 2:42 pm

DSC_6994.JPG

hinv -mv

Code: Select all

CPU: MIPS R12000 Processor Chip Revision: 3.5
FPU: MIPS R12010 Floating Point Chip Revision: 0.0
1 400 MHZ IP32 Processor
Main memory size: 1024 Mbytes
Secondary unified instruction/data cache size: 2 Mbytes on Processor 0
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
FLASH PROM version 4.18
Integral SCSI controller 0: Version ADAPTEC 7880
  Disk drive: unit 2 on SCSI controller 0 (unit 2)
  CDROM: unit 4 on SCSI controller 0
Integral SCSI controller 1: Version ADAPTEC 7880
Integral SCSI controller 2: Version Fibre Channel QL2342 Port 1, 33 MHz PCI
Integral SCSI controller 3: Version Fibre Channel QL2342 Port 2, 33 MHz PCI
On-board serial ports: tty1
On-board serial ports: tty2
On-board EPP/ECP parallel port
CRM graphics installed
Integral Ethernet: ec0, version 1
Iris Audio Processor: version A3 revision 0
  PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 1
  PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x2312) PCI slot 3
  PCI Adapter ID (vendor 0x1077, device 0x2312) PCI slot 3
Video: MVP unit 0 version 1.4
AV: AV1 Card version 1, Camera not connected.
Vice: TRE
1600SW Flat Panel adapter board and display.


/usr/gfx/gfxinfo -v

Code: Select all

Graphics board 0 is "CRM" graphics.
        Managed (":0.0") 1600x1024
        32 bitplanes
        board revision 2, CRM revision C, GBE revision B
        Timing table flags:
         Monitor 0 type: Unknown
        Channel 0:
         Origin = (0,0)
         Video Output: 1600 pixels, 1024 lines, 60.00Hz (1600x1024_60p)
         Video Format Flags:  (none)
         Sync Disabled
         Using Gamma Map 0


scsicontrol -i /dev/scsi/sc*

Code: Select all

/dev/scsi/sc0d2l0:  Disk          SEAGATE ST336753LC      0003
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc0d4l0:  CD-ROM        TOSHIBA DVD-ROM SD-M14011F09
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  synch linkedcmds
Device is  not ready


I've got the Ensemble Carbon analog component breakout box for the video option, plus a Miranda Vivo SDI dongle. So it can capture or play composite, component analogue or SDI video depending on what's attached. With the QL2342 it's easy to attach a good amount of storage for video, although the O2 lacks bandwidth to use the dual 2Gb FC card to it's full potential.

And yes, it is a real O2+ even though it has blue skins:
DSC_6995.JPG
Now this is a deep dark secret, so everybody keep it quiet :)
It turns out that when reset, the WD33C93 defaults to a SCSI ID of 0, and it was simpler to leave it that way... -- Dave Olson, in comp.sys.sgi

Currently in commercial service: Image :Onyx2:(2x) :O3x02L:
In the museum: almost every MIPS/IRIX system.
Wanted: GM1 board for Professional Series GT graphics (030-0076-003, 030-0076-004)

User avatar
zackwatt
Posts: 460
Joined: Sun Mar 01, 2009 9:53 am
Location: Kentucky

Re: O2+ 400MHz R12K, 1GB RAM, DVD, 1600SW, 2Gbit FC, blue sk

Unread postby zackwatt » Tue Dec 14, 2010 10:51 pm

Absolutly Beautiful!

Sorry its not purple though...
:Octane2: :Octane2: :Octane: :Indigo2IMP: :Indigo2: :O2: :O2+:

Octane2 2x600 V12 8GB
- Octane2 600 V12 2GB - Octane 2x400 V10 2GB
Indigo² 195 Max Impact 386MB - Indigo² 250 Extreme 386MB
O2 350 CRM 256MB - O2+ 400 CRM 512MB

"I'm totally unappreciated in my time. You can run this whole park from this room, with minimal staff, for up to three days. You think that kind of automation is easy? Or cheap? You know anybody who can network eight Connection Machines and de-bug two million lines of code for what I bid this job? Because if you can, I'd love to see him try."

User avatar
jan-jaap
Posts: 4065
Joined: Thu Jun 17, 2004 11:35 am
Location: Wijchen, The Netherlands

Re: O2+ 400MHz R12K, 1GB RAM, DVD, 1600SW, 2Gbit FC, blue sk

Unread postby jan-jaap » Wed Dec 15, 2010 4:01 am

zackwatt wrote:Sorry its not purple though...

Yeah, I'll have to buy a Tezro to make up for the lack of purple-ness in the house :)

If someone had broken the original skin and replaced it with something different, that would be a pity. Now I don't really care.

The O2+ was introduced in August 2001. This system has various components dated around that time, and the (original) system disk is from August 2001, loaded with IRIX 6.5.13. I guess they used their inventory of blue skins on the initial O2+ systems.
Now this is a deep dark secret, so everybody keep it quiet :)
It turns out that when reset, the WD33C93 defaults to a SCSI ID of 0, and it was simpler to leave it that way... -- Dave Olson, in comp.sys.sgi

Currently in commercial service: Image :Onyx2:(2x) :O3x02L:
In the museum: almost every MIPS/IRIX system.
Wanted: GM1 board for Professional Series GT graphics (030-0076-003, 030-0076-004)

User avatar
zackwatt
Posts: 460
Joined: Sun Mar 01, 2009 9:53 am
Location: Kentucky

Re: O2+ 400MHz R12K, 1GB RAM, DVD, 1600SW, 2Gbit FC, blue sk

Unread postby zackwatt » Wed Dec 15, 2010 2:18 pm

Either way, it is still an amazing system!

Here is some purple for this thread, lol.

IMG_6581.jpg


IMG_6583.jpg
:Octane2: :Octane2: :Octane: :Indigo2IMP: :Indigo2: :O2: :O2+:

Octane2 2x600 V12 8GB
- Octane2 600 V12 2GB - Octane 2x400 V10 2GB
Indigo² 195 Max Impact 386MB - Indigo² 250 Extreme 386MB
O2 350 CRM 256MB - O2+ 400 CRM 512MB

"I'm totally unappreciated in my time. You can run this whole park from this room, with minimal staff, for up to three days. You think that kind of automation is easy? Or cheap? You know anybody who can network eight Connection Machines and de-bug two million lines of code for what I bid this job? Because if you can, I'd love to see him try."


Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 1 guest