Code:
# hinv -vm
Location: /hw/module/001c01/node
IP34 Board: barcode MMN520 part 030-1707-003 rev -H
Location: /hw/module/001c01/node/cpubus/0
IP34PIMM Board: barcode MRS271 part 030-1730-001 rev -G
Location: /hw/module/001c01/Ibrick/xtalk/13
ASTODY Board: barcode MNV150 part 030-1726-003 rev -F
Location: /hw/module/001c01/Ibrick/xtalk/14
IP34 Board: barcode MMN520 part 030-1707-003 rev -H
Location: /hw/module/001c01/Ibrick/xtalk/15
IP34 Board: barcode MMN520 part 030-1707-003 rev -H
1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.3
FPU: MIPS R14010 Floating Point Chip Revision: 2.3
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor Chip (enabled)
Processor revision: 2.3. Scache: Size 4 MB Speed 300 Mhz Tap 0xa
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
Bank 0 contains 1024 MB (Priemum) DIMMS (enabled)
Integral SCSI controller 2: Version IEEE1394 SBP2
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Disk drive: unit 2 on SCSI controller 0 (unit 2)
Disk drive: unit 3 on SCSI controller 0 (unit 3)
Integral SCSI controller 1: Version QL12160, single ended
CDROM: unit 5 on SCSI controller 1
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V12
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
Iris Audio Processor: version MAD revision 1, number 1
PCI Adapter ID (vendor 0x10ee, device 0xd151) PCI slot 2
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 2
PCI Adapter ID (vendor 0x10a9, device 0x0005) PCI slot 3
PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
SD-DIGVID Standard Definition Digital Video: unit 0, revision 2.75.0
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
Dual Channel Display
IP35prom in Module 001c01/Slot n0: Revision 6.210
DMediaPro DM10 FW option: unit 0, revision 1.1.0
USB controller: type OHCI
Code:
# /usr/gfx/gfxinfo -vv
Graphics board 0 is "ODYSSEY" graphics.
Managed (":0.0") 2560x1024
BUZZ version B.1
PB&J version 1
128MB memory
Banks: 4, CAS latency: 3
Monitor 0 type: Unknown
Dual Channel Display option
Monitor 1 type: SGX -8192 Monitor 2 type: DEL -8189
Input Sync: Voltage - Video Level; Source - Internal; Genlocked - False
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (2@1280x1024_60)
Video Format Flags: (none)
Sync Disabled
Using Gamma Map 0
Monitor Type: SGX-8192
Gain (all color components) - 0.000000 ; range [1,10]
Channel 1:
Origin = (1280,0)
Video Output: 1280 pixels, 1024 lines, 60.00Hz (2@1280x1024_60)
Video Format Flags: (none)
Sync Disabled
Using Gamma Map 0
Monitor Type: DEL-57347
Gain (all color components) - 0.000000 ; range [1,10]
Code:
# diskpatch -v
sc0d1l0: Disk QUANTUM ATLAS 10K 18WLS UCHQ Serial: 11192214
sc0d2l0: Disk QUANTUM ATLAS 10K 18WLS UCHQ Serial: 11193274
sc0d3l0: Disk SEAGATE ST3300007LW 0003 Serial: 3KR0NFHN
The firewire board installed
is this one. It seems to work well enough, I was able to access the ATA disk in the no-name external firewire case that I use for my OS X Time Machine backup drive <semi-interesting, because that no-name case has an Initio chipset instead of the Oxford 911 mentioned in the Fuel hardware Aggregator>.
Code:
# fwprobe
Probing DM10 cards...
Number of cards: 1
Card Info
=========
Card #: 0
Name : DM10
ID : 0x5160000030E0A
Ports : 3
Speed : 400 / 400
2 devices attached
Device 0: 0x5160000030E0A
Vendor: Silicon Graphics, Inc.
Model: Unknown
Proto: Unknown
Device 1: 0x10100500400606
Vendor: INITIO CORPORATION
Model: ST3200822A
Proto: SBP2
The DM6 appears in an hinv, mlquery, and passes all of the tests in /usr/diags/ML/tests. All I need now is an SD video feed...
Code:
# mlquery -d sd-digvid
DEVICE: sd-digvid
parent: Fuel.
index: 0
version: 2.5.33.111
location: PCI,card:0
jacks: VideoIn,
VideoOut
paths: VideoToMemory,
MemoryToVideo
Attachment:
Fuel-n-F180.jpg [ 120.51 KiB | Viewed 418 times ]
Login
Register
FAQ
Search
Maxed out - Nice! And you got an original F180 for it!
"Octanium": 300 MHz, R12k, 512MB, Impact SR
"IROX": (x4) 600 MHz, R14k, 4GB
Unfortunately, I no longer have this. (Moved and couldn't take.)