Origin 350: 16xR16K 700MHz, 4GB RAM

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
ramq
Posts: 771
Joined: Fri Jan 25, 2008 6:06 am
Location: Sweden

Origin 350: 16xR16K 700MHz, 4GB RAM

Unread postby ramq » Sat Dec 12, 2009 4:06 pm

May I present 'Venom', my newly downsized Origin 350 multi-brick config!
This is what's left at the moment from my rescent aquire and is trimmed down to a more manageable size (=less powerdraw).

Code: Select all

hinv -vm
Location: /hw/module/001c01/node
       IP53_4CPU Board: barcode MXD727     part 030-1868-001 rev -C
Location: /hw/module/001c01/IXbrick/xtalk/15
       2U_INT_53 Board: barcode MTZ152     part 030-1809-003 rev -B
Location: /hw/module/001c01/IXbrick/xtalk/15/pci-x/0/1/ioc4
             IO9 Board: barcode MTS407     part 030-1771-005 rev -A
Location: /hw/module/001c02/node
       IP53_4CPU Board: barcode MXM753     part 030-1868-001 rev -C
Location: /hw/module/001c02/IXbrick/xtalk/15
       2U_INT_53 Board: barcode MTC260     part 030-1809-003 rev -A
Location: /hw/module/001c02/IXbrick/xtalk/15/pci-x/0/1/ioc4
             IO9 Board: barcode MTS540     part 030-1771-005 rev -A
Location: /hw/module/001c03/node
       IP53_4CPU Board: barcode MTA290     part 030-1868-001 rev -C
Location: /hw/module/001c03/IXbrick/xtalk/15
       2U_INT_53 Board: barcode MTC253     part 030-1809-003 rev -A
Location: /hw/module/001c04/node
       IP53_4CPU Board: barcode MTA291     part 030-1868-001 rev -C
Location: /hw/module/001c04/IXbrick/xtalk/15
       2U_INT_53 Board: barcode MTV599     part 030-1809-003 rev -A
Location: /hw/module/001r05/router
          ROUTER Board: barcode MVA352     part 030-1634-003 rev -A
16 700 MHZ IP35 Processors
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 1 at Module 001c01/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 2 at Module 001c01/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 3 at Module 001c01/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 4 at Module 001c02/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 5 at Module 001c02/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 6 at Module 001c02/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 7 at Module 001c02/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 8 at Module 001c03/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 9 at Module 001c03/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 10 at Module 001c03/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 11 at Module 001c03/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 12 at Module 001c04/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 13 at Module 001c04/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 14 at Module 001c04/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
CPU 15 at Module 001c04/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)
  Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz  Tap 0xc
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 1024 MB (enabled)
  Bank 0 contains 512 MB (Premium) DIMMS (enabled)
  Bank 1 contains 512 MB (Premium) DIMMS (enabled)
Memory at Module 001c02/Slot 0: 1024 MB (enabled)
  Bank 0 contains 512 MB (Premium) DIMMS (enabled)
  Bank 1 contains 512 MB (Premium) DIMMS (enabled)
Memory at Module 001c03/Slot 0: 1024 MB (enabled)
  Bank 0 contains 512 MB (Premium) DIMMS (enabled)
  Bank 1 contains 512 MB (Premium) DIMMS (enabled)
Memory at Module 001c04/Slot 0: 1024 MB (enabled)
  Bank 0 contains 512 MB (Premium) DIMMS (enabled)
  Bank 1 contains 512 MB (Premium) DIMMS (enabled)
ROUTER in Module 001c01/Slot 0: Revision 1: Active Ports [2,3,4,5,] (enabled)
Integral SCSI controller 19: Version IDE (ATA/ATAPI) IOC4
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
  CDROM: unit 0 on SCSI controller 2
Integral SCSI controller 20: Version QL12160, low voltage differential
Integral SCSI controller 21: Version QL12160, low voltage differential
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty27
IOC3/IOC4 serial port: tty28
IOC3/IOC4 serial port: tty29
IOC3/IOC4 serial port: tty30
IOC3/IOC4 serial port: tty23
IOC3/IOC4 serial port: tty24
IOC3/IOC4 serial port: tty25
IOC3/IOC4 serial port: tty26
Gigabit Ethernet: tg6, module 001c02, PCI bus 1 slot 4
Integral Gigabit Ethernet: tg0, module 001c01, PCI bus 1 slot 4
  PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
  PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
IOC4 firmware revision 79
IOC4 firmware revision 79
IOC3/IOC4 external interrupts: 6
IOC3/IOC4 external interrupts: 1
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
HUB in Module 001c02/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
HUB in Module 001c03/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
HUB in Module 001c04/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
IP35prom in Module 001c02/Slot n0: Revision 6.210
IP35prom in Module 001c03/Slot n0: Revision 6.210
IP35prom in Module 001c04/Slot n0: Revision 6.210


Code: Select all

l1cmd serial all

Data                            Location      Value
------------------------------  ------------  --------
Local System Serial Number      NVRAM         M2100629
Reference System Serial Number  NVRAM         M2100629
Local Brick Serial Number       EEPROM        MTZ152
Reference Brick Serial Number   NVRAM         MTZ152


EEPROM      Product Name    Serial      Part Number           Rev  T/W
----------  --------------  ----------  --------------------  ---  ------
INTERFACE   2U_INT_53       MTZ152      030_1809_003          B    00
IO9         IO9             MTS407      030_1771_005          A    00
ODYSSEY     no hardware detected
RISER       2U_RISER        MXN357      030_1808_005          A    00
NODE        IP53_4CPU       MXD727      030_1868_001          C    00

EEPROM     JEDEC-SPD Info           Part Number        Rev Speed  SGI
---------- ------------------------ ------------------ --- ------ --------
DIMM 0     CE000000000000005FF40800 M3 46L6510BT1-CA0  0B   10.0  NO DATA
DIMM 2     no hardware detected
DIMM 4     no hardware detected
DIMM 6     no hardware detected
DIMM 1     CE000000000000005FC80C00 M3 46L6510BT1-CA0  0B   10.0  NO DATA
DIMM 3     no hardware detected
DIMM 5     no hardware detected
DIMM 7     no hardware detected


Code: Select all

l1cmd env
Environmental monitoring is enabled and running.

Description    State       Warning Limits     Fault Limits       Current
-------------- ----------  -----------------  -----------------  -------
           12V   Disabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
           12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
            5V    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    4.97
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32
        12V IO    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.06
        5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04
      3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27
        5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04
          3.3V    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.32
          2.5V    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.51
          1.8V    Enabled  10%   1.62/  1.98  20%   1.44/  2.16    1.78
      3.3V aux   Disabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27
  XIO 12V bias   Disabled  10%  10.80/ 13.20  20%   9.60/ 14.40    0.00
        XIO 5V   Disabled  10%   4.50/  5.50  20%   4.00/  6.00    0.00
      XIO 2.5V   Disabled  10%   2.25/  2.75  20%   2.00/  3.00    0.00
  XIO 3.3V aux   Disabled  10%   2.97/  3.63  20%   2.64/  3.96    0.00
NODE0 3.3V aux    Enabled  10%   2.97/  3.63  20%   2.64/  3.96    3.27
  NODE0 5V aux    Enabled  10%   4.50/  5.50  20%   4.00/  6.00    5.04
     NODE0 12V    Enabled  10%  10.80/ 13.20  20%   9.60/ 14.40   12.00
    NODE0 SRAM    Enabled  10%   2.25/  2.75  20%   2.00/  3.00    2.50
    NODE0 1.5V    Enabled  10%   1.35/  1.65  20%   1.20/  1.80    1.49
     NODE0 CPU    Enabled  10%   1.13/  1.38  20%   1.00/  1.50    1.25

Description    State       Warning RPM  Current RPM
-------------- ----------  -----------  -----------
FAN 0  EXHST 1    Enabled         2160         2305
FAN 1  EXHST 2    Enabled         2160         2305
FAN 2       PS    Enabled         1575         1980
FAN 3    PCI 1    Enabled         2160         2589
FAN 4    PCI 2    Enabled         2160         2877

                           Advisory   Critical   Fault      Current
Description    State       Temp       Temp       Temp       Temp
-------------- ----------  ---------  ---------  ---------  ---------
INTERFACE 0       Enabled   31C/ 87F   48C/118F   55C/131F    5C/ 41F -23-
INTERFACE 1       Enabled   31C/ 87F   48C/118F   55C/131F    6C/ 42F -23-
INTERFACE 2       Enabled   31C/ 87F   48C/118F   55C/131F   11C/ 51F -13-
PCI RISER         Enabled   31C/ 87F   48C/118F   55C/131F   10C/ 50F -11-
ODYSSEY          Disabled
NODE              Enabled   31C/ 87F   48C/118F   55C/131F    8C/ 46F -14-
BEDROCK           Enabled   31C/ 87F   48C/118F   55C/131F    3C/ 37F -31-


Code: Select all

scsicontrol -i /dev/scsi/sc*
/dev/scsi/sc0d1l0:  Disk          COMPAQ  BD1468A4B5      HPB8
ANSI vers 3, ISO ver: 0, ECMA ver: 0; supports:  16bit synch linkedcmds cmdqueing
Device is  ready
/dev/scsi/sc2d0l0:  CD-ROM        MATSHITADVD-ROM SR-8178 PZ21
ANSI vers 0, ISO ver: 0, ECMA ver: 0; supports:
Device is  not ready


Code: Select all

/sbin/diskpatch -v
sc0d1l0:  Disk         COMPAQ  BD1468A4B5      HPB8  Serial: J405XJ1K
:O3200: :Fuel: :Indy: :O3x02L:

User avatar
recondas
Moderator
Moderator
Posts: 5441
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Re: Origin 350: 16xR16K 700MHz, 4GB RAM

Unread postby recondas » Sat Dec 12, 2009 6:00 pm

Very nice! Any plans to add graphics?

BTW, were you able to use the pin-out information to set up a power supply for your L2 controller? Like you, I have two systems with L2 controllers, and have I've found the L3 software to be very handy as an overall controller/remote monitoring tool for both systems. I run it on the same lightweight system used as a Synergy host <run so I can share a single keyboard and mouse between the Onyx 300, Onyx 350, a PC and a Mac>.
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************

User avatar
hamei
Posts: 10433
Joined: Tue Feb 24, 2004 4:10 pm
Location: over the rainbow

Re: Origin 350: 16xR16K 700MHz, 4GB RAM

Unread postby hamei » Sun Dec 13, 2009 12:02 am

recondas wrote: < so I can share a single keyboard and mouse between the Onyx 300, Onyx 350, a PC and a Mac>.

I hate to say this, but have you guys considered the possibility that maybe you're getting a little carried away ? :shock:

User avatar
guardian452
Donor
Donor
Posts: 3429
Joined: Tue Aug 21, 2007 10:12 pm
Location: United States
Contact:

Re: Origin 350: 16xR16K 700MHz, 4GB RAM

Unread postby guardian452 » Sun Dec 13, 2009 11:41 am

well, good keyboards and mice ARE hard to find ;)

User avatar
foetz
Moderator
Moderator
Posts: 6544
Joined: Mon Apr 14, 2003 4:34 am
Contact:

Re: Origin 350: 16xR16K 700MHz, 4GB RAM

Unread postby foetz » Sun Dec 13, 2009 10:35 pm

sybrfreq wrote:well, good keyboards and mice ARE hard to find ;)


indeed. i'm always stocking up granite kb and mice as good as i can :D

ramq
Posts: 771
Joined: Fri Jan 25, 2008 6:06 am
Location: Sweden

Re: Origin 350: 16xR16K 700MHz, 4GB RAM

Unread postby ramq » Mon Dec 14, 2009 2:19 am

recondas wrote:Very nice! Any plans to add graphics?

Well, yes and no. I'm planning on incorporating the famous "V10 hack", but it's on very low priority cause I currently don't need graphics on it, other than for fun. A little FW-card and USB will probably pimp this machine a little further, but nothing planned further than that.
Well, apart from memory that is. (Currently I have some 2GB kits in hopefully a couple of weeks.)

BTW, were you able to use the pin-out information to set up a power supply for your L2 controller? Like you, I have two systems with L2 controllers, and have I've found the L3 software to be very handy as an overall controller/remote monitoring tool for both systems.

Well, actually I haven't had time for it yet. Had some spare time this weekend to fire up this thing, plus diagnosing other bricks, etc. I'll probably measure the pinout next time I'll dedicate time for the O3800 system + power measuring.
So far this hasn't been a problem though, since the L3 software takes care of all my needs so far. Only drawback is that L1-reconfigs (changing rack/slot numbers + associated reboot) crap things up on the little Linux-bugger, so I have to reboot it every time I make such changes.
:O3200: :Fuel: :Indy: :O3x02L:


Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 1 guest