Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
User avatar
mapesdhs
Posts: 2516
Joined: Mon Nov 10, 2003 4:17 pm
Location: Edinburgh, Scotland
Contact:

Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby mapesdhs » Sat Jun 06, 2009 8:01 am

Tezro Quad-R16K/1GHz (16MB L2), 4GB RAM, 36GB 10K system, 48 x 146GB 15K JBOD RAID, 4 x QLA12160/66 PCI64,
DM3 card (not in hinv as drivers not installed). Normally connected to a DM5/VBOB, but again not shown here. The system
originally had two QLA2342s, RAD Audio, dual-port Gbit NIC and dual-port serial card, but I've removed all these.

Code: Select all

Location: /hw/module/001c01/node
       IP59_4CPU Board: barcode NPD130     part 030-1989-003 rev -A
Location: /hw/module/001c01/IXbrick/xtalk/11
       WS_INT_53 Board: barcode NNY839     part 030-1881-007 rev -A
Location: /hw/module/001c01/IXbrick/xtalk/12
      ODY128B1_2 Board: barcode NNR309     part 030-1884-005 rev -B
Location: /hw/module/001c01/IXbrick/xtalk/15
       WS_INT_53 Board: barcode NNY839     part 030-1881-007 rev -A
Location: /hw/module/001c01/IXbrick/xtalk/15/pci-x/0/1/ioc4
             IO9 Board: barcode NKY494     part 030-1771-005 rev -A
4 1.0 GHZ IP35 Processors
CPU: MIPS R16000 Processor Chip Revision: 3.0
FPU: MIPS R16010 Floating Point Chip Revision: 3.0
CPU 0 at Module 001c01/Slot 0/Slice A: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 1 at Module 001c01/Slot 0/Slice B: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 2 at Module 001c01/Slot 0/Slice C: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
CPU 3 at Module 001c01/Slot 0/Slice D: 1.0 Ghz MIPS R16000 Processor Chip (enabled)
  Processor revision: 3.0. Scache: Size 16 MB Speed 333 Mhz  Tap 0x15
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 16 Mbytes
Memory at Module 001c01/Slot 0: 4096 MB (enabled)
  Bank 0 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 1 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 2 contains 1024 MB (Premium) DIMMS (enabled)
  Bank 3 contains 1024 MB (Premium) DIMMS (enabled)
Integral SCSI controller 15: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 15 (unit 8)
  Disk drive: unit 9 on SCSI controller 15 (unit 9)
  Disk drive: unit 10 on SCSI controller 15 (unit 10)
  Disk drive: unit 11 on SCSI controller 15 (unit 11)
  Disk drive: unit 12 on SCSI controller 15 (unit 12)
  Disk drive: unit 13 on SCSI controller 15 (unit 13)
Integral SCSI controller 16: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 16 (unit 8)
  Disk drive: unit 9 on SCSI controller 16 (unit 9)
  Disk drive: unit 10 on SCSI controller 16 (unit 10)
  Disk drive: unit 11 on SCSI controller 16 (unit 11)
  Disk drive: unit 12 on SCSI controller 16 (unit 12)
  Disk drive: unit 13 on SCSI controller 16 (unit 13)
Integral SCSI controller 7: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 7 (unit 8)
  Disk drive: unit 9 on SCSI controller 7 (unit 9)
  Disk drive: unit 10 on SCSI controller 7 (unit 10)
  Disk drive: unit 11 on SCSI controller 7 (unit 11)
  Disk drive: unit 12 on SCSI controller 7 (unit 12)
  Disk drive: unit 13 on SCSI controller 7 (unit 13)
Integral SCSI controller 8: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 8 (unit 8)
  Disk drive: unit 9 on SCSI controller 8 (unit 9)
  Disk drive: unit 10 on SCSI controller 8 (unit 10)
  Disk drive: unit 11 on SCSI controller 8 (unit 11)
  Disk drive: unit 12 on SCSI controller 8 (unit 12)
  Disk drive: unit 13 on SCSI controller 8 (unit 13)
Integral SCSI controller 11: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 11 (unit 8)
  Disk drive: unit 9 on SCSI controller 11 (unit 9)
  Disk drive: unit 10 on SCSI controller 11 (unit 10)
  Disk drive: unit 11 on SCSI controller 11 (unit 11)
  Disk drive: unit 12 on SCSI controller 11 (unit 12)
  Disk drive: unit 13 on SCSI controller 11 (unit 13)
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
  CDROM: unit 0 on SCSI controller 2
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, low voltage differential
Integral SCSI controller 12: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 12 (unit 8)
  Disk drive: unit 9 on SCSI controller 12 (unit 9)
  Disk drive: unit 10 on SCSI controller 12 (unit 10)
  Disk drive: unit 11 on SCSI controller 12 (unit 11)
  Disk drive: unit 12 on SCSI controller 12 (unit 12)
  Disk drive: unit 13 on SCSI controller 12 (unit 13)
Integral SCSI controller 17: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 17 (unit 8)
  Disk drive: unit 9 on SCSI controller 17 (unit 9)
  Disk drive: unit 10 on SCSI controller 17 (unit 10)
  Disk drive: unit 11 on SCSI controller 17 (unit 11)
  Disk drive: unit 12 on SCSI controller 17 (unit 12)
  Disk drive: unit 13 on SCSI controller 17 (unit 13)
Integral SCSI controller 18: Version QL12160, low voltage differential
  Disk drive: unit 8 on SCSI controller 18 (unit 8)
  Disk drive: unit 9 on SCSI controller 18 (unit 9)
  Disk drive: unit 10 on SCSI controller 18 (unit 10)
  Disk drive: unit 11 on SCSI controller 18 (unit 11)
  Disk drive: unit 12 on SCSI controller 18 (unit 12)
  Disk drive: unit 13 on SCSI controller 18 (unit 13)
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
Graphics board: V12
Integral Gigabit Ethernet: tg0, module 001c01, PCI bus 1 slot 4
Iris Audio Processor: version MAD revision 1, number 1
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 2
  PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
  PCI Adapter ID (vendor 0x104c, device 0xac28) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
  PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
  PCI Adapter ID (vendor 0x1412, device 0x1724) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
IOC4 firmware revision 83
IOC3/IOC4 external interrupts: 1
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210

Graphics board 0 is "ODYSSEY" graphics.
        Managed (":0.0") 1600x1200
        BUZZ version B.2
        PB&J version 1
        128MB memory
                Banks: 4, CAS latency: 3
         Monitor 0 type: Unknown
        Channel 0:
         Origin = (0,0)
         Video Output: 1600 pixels, 1200 lines, 72.01Hz (1600x1200_72)


tezro# df
Filesystem             Type  kbytes     use     avail  %use Mounted on
/dev/root               xfs 35428556 17487404 17941152  50  /
/dev/xlv/video          xfs 6881757136 10590800 6871166336   1  /video



I have a second similar system (same CPU/gfx/RAM) that still has the original other cards.

Ian.
I'm working on a charitable PC build for the Learn Engineering YouTube channel. Please PM/email/call if you'd like to contribute!
Donations of any kind of item I can sell to provide funds are also most welcome.
mapesdhs@yahoo.com
+44 (0)7434 635 121

User avatar
indyman007
Posts: 919
Joined: Wed Aug 20, 2008 5:38 am
Location: North of England

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby indyman007 » Sat Jun 06, 2009 8:07 am

Do you have any particular use for it?
:Indy: R4600PC 133 MHz

Mac Mini 2.5GHz 8GB RAM
Raspberry Pi

User avatar
bri3d
Posts: 669
Joined: Sat Jun 28, 2008 11:08 am
Location: Boulder, CO

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby bri3d » Sat Jun 06, 2009 8:13 am

This is what I hope to turn my O350/Onyx system into - all I'm missing is my NUMALink cable (on the way), a V12 (to replace my V10), and a DM3 (I probably won't end up getting one, as I don't have much use, but...) and I've got it :p

@indyman007 - would probably be used as a Discreet system in "the real world" - there's not much else that uses a DM3 and that much power.

sgtprobe
Posts: 333
Joined: Thu Nov 20, 2008 11:18 pm
Location: Sweden
Contact:

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby sgtprobe » Sat Jun 06, 2009 9:51 am

Wow, Nice system Ian. :)

/Jonas
Image Image Image Image Image Image

-----------------
Old polygon wrangler
___________________
http://www.edgeloop.se

User avatar
hamei
Posts: 10435
Joined: Tue Feb 24, 2004 4:10 pm
Location: over the rainbow

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby hamei » Sat Jun 06, 2009 9:58 am

bri3d wrote:This is what I hope to turn my O350/Onyx system into - all I'm missing is my NUMALink cable (on the way), a V12 (to replace my V10), and a DM3

DM3 is the SDStationOEM ?

Ian, since you pulled the serial card, could you look and see what UART's it has ? Maybe 16550's ?

User avatar
bri3d
Posts: 669
Joined: Sat Jun 28, 2008 11:08 am
Location: Boulder, CO

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby bri3d » Sat Jun 06, 2009 12:51 pm

hamei wrote:DM3 is the SDStationOEM ?


Pretty sure that was DM6 - the DM3 is XIO, not PCI. There was some speculation that DM3 might also be a DVE product but as far as I know only SGI ever sold XIO cards, so I doubt they ever directly sold any.

User avatar
foetz
Moderator
Moderator
Posts: 6593
Joined: Mon Apr 14, 2003 4:34 am
Contact:

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby foetz » Sat Jun 06, 2009 6:36 pm

that's it.
what else to say? :D

User avatar
mapesdhs
Posts: 2516
Joined: Mon Nov 10, 2003 4:17 pm
Location: Edinburgh, Scotland
Contact:

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby mapesdhs » Sun Jun 07, 2009 5:48 pm

indyman007 writes:
> Do you have any particular use for it?

There are things I can use it for (movie conversion tasks), but neither system is for keeps. I bought them stricly as an
investment, because the ISA interest rates are now so useless. They were expensive (thousands); I couldn't justify
spending so much on something like this for personal use, not at present. My bank savings balance would have to
have at least one extra digit on the end for that to be viable. :D

A US movie company is interested in one of them, perhaps later in the summer, not sure yet.

Oh, I have a quad-700 system aswell.


bri3d writes:
> This is what I hope to turn my O350/Onyx system into - ...

Is it still a dual-1GHz V10 atm?


> replace my V10), and a DM3 (I probably won't end up getting one, as I don't have much use, but...) and I've got it :p

I got one from Harry, for the quad-700 system I have. He probably has more.


> @indyman007 - would probably be used as a Discreet system in "the real world" - there's not much else that uses
> a DM3 and that much power.

Correct, they were all Smoke systems. The unit pictured at the start of this thread still has a sticker on the front panel,
behind the front flap, that says, "SMOKE2". Naturally, the system disks were wiped though. Each system came with
either an original IR36 or IR73 Stone FC array, ie. a 15-bay FC chassis filled with either 36GB or 73GB FC drives
containing proper Discreet firmware.


sgtprobe writes:
> Wow, Nice system Ian.

Thanks! 8)

I've added a few benchmark results for the system, but have a few more to do.


hamei writes:
> Ian, since you pulled the serial card, could you look and see what
> UART's it has ? Maybe 16550's ?

The board (PN 030-1657-003, dated 2000) has just four main ASICs:

Code: Select all

- 2 x SIPEX SP333CT 0327
- TL16PIR552PH F-41A5RDW
- LSI LOGIC L2A0366 IOC3 REV C, SGI 1996, 099-0126-003, J 0416, WPG16008


There are two more much smaller 14-pin ASICs, but the writing on them is too small to discern as I type this.

I have a second serial card, marked SGI Imagesync, PN 030-1723-001. It has a completely different layout, the main
ASIC being a XILINX SPARTAN XCS40XL (PQ208AKP0029, D1106126A).

While I think of it...

The dual-port Gbit NIC in the systems is SGI PN 9210292, Tigon3 I think (Broadcom ASIC), marked Silicom Ltd
Connectivity Solutions, model number PXG2-SGI.

The RAD Audio card is PN 030-1649-001, LSI ASIC L2A0470 RAD1 REV B.

Hope this helps!


Btw, does anyone know if Blender 2.48 can do renders using networked systems? If so, is it easy to setup? I was
wondering how hard it would be to run my benchmark using all three Tezros, see what happens.

Ian.

Richtom1
Posts: 798
Joined: Sun Oct 17, 2004 5:49 pm
Location: Florida

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby Richtom1 » Sun Jun 07, 2009 6:11 pm

I'll be looking to get a set up like that next..........unless I die first :( bummer

btw the DM3 I have is PN: 030-1927-003 Rev B and it's PCI not XIO

And will you stop hitting me in the back of the head already!
Image

User avatar
mapesdhs
Posts: 2516
Joined: Mon Nov 10, 2003 4:17 pm
Location: Edinburgh, Scotland
Contact:

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby mapesdhs » Sun Jun 07, 2009 6:25 pm

Richtom1 writes:
> I'll be looking to get a set up like that next..........unless I die first :( bummer

In that case, take all possible measures to live longer. 8)


> btw the DM3 I have is PN: 030-1927-003 Rev B and it's PCI not XIO

Ah, no, it's not a PCI card. Check a DM3 installed in a Tezro, it does not plug into a PCI slot.

The only PCI SGI video board I know of is the DM6, a card Discreet never officially supported.

Ian.

User avatar
jan-jaap
Donor
Donor
Posts: 4939
Joined: Thu Jun 17, 2004 11:35 am
Location: Wijchen, The Netherlands
Contact:

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby jan-jaap » Mon Jun 08, 2009 12:40 am

hamei wrote:Ian, since you pulled the serial card, could you look and see what UART's it has ? Maybe 16550's ?

Nothing that mundane ;)

I believe there's an IOC3 on it, the IO chip from the IO6 of an O2k. The keyboard/mouse/network ports aren't wired. Is that wasteful? You betcha ... But at least they didn't need to write a new driver.
:PI: :Indigo: :Indigo: :Indy: :Indy: :Indy: :Indigo2: :Indigo2: :Indigo2IMP: :Octane: :Octane2: :O2: :O2+: Image :Fuel: :Tezro: :4D70G: :Skywriter: :PWRSeries: :Crimson: :ChallengeL: :Onyx: :O200: :Onyx2: :O3x02L:
To accentuate the special identity of the IRIS 4D/70, Silicon Graphics' designers selected a new color palette. The machine's coating blends dark grey, raspberry and beige colors into a pleasing harmony. (IRIS 4D/70 Superworkstation Technical Report)

User avatar
ShadeOfBlue
Moderator
Moderator
Posts: 799
Joined: Tue Nov 25, 2003 12:09 pm
Location: Europe

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby ShadeOfBlue » Mon Jun 08, 2009 12:54 am

jan-jaap wrote:Nothing that mundane ;)

I believe there's an IOC3 on it, the IO chip from the IO6 of an O2k. The keyboard/mouse/network ports aren't wired. Is that wasteful? You betcha ... But at least they didn't need to write a new driver.


But it does have a 16550 UART chip as well: :?

mapesdhs wrote:

Code: Select all

- TL16PIR552PH F-41A5RDW

The datasheet for this one says it has dual 16550 UARTs + parallel port.

Perhaps the IOC3 chip is just a bridge.

User avatar
mapesdhs
Posts: 2516
Joined: Mon Nov 10, 2003 4:17 pm
Location: Edinburgh, Scotland
Contact:

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby mapesdhs » Mon Jun 08, 2009 2:44 am

Just a thought about the DM3...

It fits into the same type of double-socket that the V12 is plugged into (definitely XIO, or rather XIO2 I suppose) Thus, with a
bit of metal hacking of the rear chassis plate, could one fit two V12s into a Tezro tower unit? This would mean no DM3 though.

Wild thought: if one knew how, maybe the spare XIO port could be linked to the same port in a different Tezro, make an 8-CPU
system. Hmm, probably not.

Funny thing - before Tezro launched, some of the comments I heard from SGI people led me to infer that the system would
indeed be linkable in this way, but alas that didn't happen. Pity, would've been cool.

Ian.

User avatar
recondas
Moderator
Moderator
Posts: 5441
Joined: Sun Jun 06, 2004 5:55 pm
Location: NC - USA

Dual-Pipe Tezro Tower?

Unread postby recondas » Mon Jun 08, 2009 3:12 am

mapesdhs wrote:Funny thing - before Tezro launched, some of the comments I heard from SGI people led me to infer that the system would indeed be linkable in this way, but alas that didn't happen. Pity, would've been cool.

I believe it did happen - if you purchased a Tezro rack system you could link <at least> two.

Though interestingly enough, the rear view illustration in the Tezro Rack Mounted Workstation User's Guide doesn't label the XIO port , or specifically mention it in the accompanying text.

While the nearly identical illustration from the Onyx 350 Visualization System User's Guide does.

An implicit omission to prevent drawing sales from the more expensive Onyx 350 line?
***********************************************************************
Welcome to ARMLand - 0/0x0d00
running...(sherwood-root 0607201829)
* InfiniteReality/Reality Software, IRIX 6.5 Release *
***********************************************************************

kramlq
Donor
Donor
Posts: 994
Joined: Tue Sep 20, 2005 5:10 pm
Location: IRL

Re: Tezro, Quad-R16K/1GHz (16MB L2), 4GB, V12/DM3, RAID

Unread postby kramlq » Mon Jun 08, 2009 3:51 am

...where in Edinburgh do you live ... any summer holidays planned ... do you have an alarm system on your house...

On a serious note - an amazing system, but why only 4Gb RAM in such an otherwise highly spec'ed machine?


Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 2 guests