Onyx R10k 2 x 195MHz 512MB RAM RE2

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
zski128
Posts: 225
Joined: Wed Feb 09, 2005 11:53 am
Location: Boston, MA
Contact:

Onyx R10k 2 x 195MHz 512MB RAM RE2

Unread postby zski128 » Sat Nov 27, 2010 8:31 pm

Code: Select all

hinv -vm
CPU Board at Slot 2: (Enabled)
  Processor 0 at Slot 2/Slice 0: 194 Mhz R10000 with 1 MB secondary cache (Enabled)
  Processor 1 at Slot 2/Slice 1: 194 Mhz R10000 with 1 MB secondary cache (Enabled)
CPU: MIPS R10000 Processor Chip Revision: 2.6
FPU: MIPS R10010 Floating Point Chip Revision: 2.6
Main memory size: 512 Mbytes, 2-way interleaved
MC3 Memory Board at Slot 1: 512 MB of memory (Enabled)
  Bank A contains 16 MB SIMMS (Enabled)
  Bank B contains 16 MB SIMMS (Enabled)
  Bank C contains 16 MB SIMMS (Enabled)
  Bank D contains 16 MB SIMMS (Enabled)
  Bank E contains 16 MB SIMMS (Enabled)
  Bank F contains 16 MB SIMMS (Enabled)
  Bank G contains 16 MB SIMMS (Enabled)
  Bank H contains 16 MB SIMMS (Enabled)
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 1 Mbyte
Integral SCSI controller 0: Version WD33C95A, single ended, revision 0
  CDROM: unit 5 on SCSI controller 0
Integral SCSI controller 1: Version WD33C95A, differential, revision 0
  Disk drive: unit 1 on SCSI controller 1 (unit 1)
  Disk drive: unit 2 on SCSI controller 1 (unit 2)
Integral EPC serial ports: 4
Integral EPC parallel port: Ebus slot 3
RealityEngineII Graphics Pipe 0 at IO Slot 3 Physical Adapter 2 (Fchip rev 2)
Integral Ethernet controller: et0, Ebus slot 3
I/O board, Ebus slot 3: IO4 revision 1
VME bus: adapter 13
VME bus: adapter 0 mapped to adapter 13
EPC external interrupts


Code: Select all

/usr/gfx/gfxinfo
Graphics board 0 is "RES" graphics.
        Managed (":0.0") 1280x1024
        Display 1280x1024 @ 60Hz
        12 GE (GE10 rev. 0x7)
        1 RM4 board
        Small pixel depth
        10-bit RGBA pixels
        Not using Multi-Channel Option


No pics yet as its all taken apart at the moment.
:O2000: :Indigo: :Indy: x2 :Octane: :O2: :Fuel:WIP :1600SW:x2

Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 1 guest