CMN-A015 O2k system 8x250Mhz

henrycault · **Posted:** Wed Jul 29, 2009 5:42 pm

Here's my hinv output, Thanks a lot for the help i got from this board, and all previous posts, i did manage to make it work. At least on 7 of it's cpus.

Code:

Location: /hw/module/1/slot/n1/node
        MODULEID Board: barcode K0017640   part              rev
            IP31 Board: barcode HXN157     part 030-1255-003 rev  D
        IP31PIMM Board: barcode HXR161     part 030-1313-002 rev  A
       8P12_MPLN Board: barcode HXD826     part 030-0762-006 rev  K
Location: /hw/module/1/slot/n2/node
            IP31 Board: barcode HTK556     part 030-1255-003 rev  B
        IP31PIMM Board: barcode HTV192     part 030-1313-002 rev  A
Location: /hw/module/1/slot/n3/node
            IP31 Board: barcode HXH456     part 030-1255-003 rev  D
        IP31PIMM Board: barcode HXF394     part 030-1313-002 rev  A
Location: /hw/module/1/slot/n4/node
            IP31 Board: barcode HXN148     part 030-1255-003 rev  D
        IP31PIMM Board: barcode HXG351     part 030-1313-002 rev  A
Location: /hw/module/1/slot/r1/router
      ROUTER_IR1 Board: barcode HRM549     part 030-0841-003 rev  B
Location: /hw/module/1/slot/r2/router
      ROUTER_IR1 Board: barcode HAP382     part 030-0841-003 rev  B
Location: /hw/module/1/slot/io4/xtalk_pci
       XTALK_PCI Board: barcode HXF987     part 030-1275-002 rev  B
Location: /hw/module/1/slot/io7/mscsi
           MSCSI Board: barcode HMH301     part 030-1243-001 rev  M
Location: /hw/module/1/slot/io1/baseio
          BASEIO Board: barcode HLR950     part 030-1124-002 rev  M
7 250 MHZ IP27 Processors
CPU: MIPS R10000 Processor Chip Revision: 3.4
FPU: MIPS R10010 Floating Point Chip Revision: 3.4
CPU 0 at Module 1/Slot 1/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 1 at Module 1/Slot 1/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 2 at Module 1/Slot 2/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 7 at Module 1/Slot 2/Slice B: 250 Mhz MIPS R10000 Processor Chip (disabled)

  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 3 at Module 1/Slot 3/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 4 at Module 1/Slot 3/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 5 at Module 1/Slot 4/Slice A: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
CPU 6 at Module 1/Slot 4/Slice B: 250 Mhz MIPS R10000 Processor Chip (enabled)
  Processor revision: 3.4. Scache: Size 4 MB Speed 250 Mhz  Tap 0x9
Main memory size: 4096 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 1/Slot 1: 1024 MB (enabled)
  Bank 0 contains 512 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 2: 1024 MB (enabled)
  Bank 0 contains 512 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 3: 1024 MB (enabled)
  Bank 0 contains 512 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Memory at Module 1/Slot 4: 1024 MB (enabled)
  Bank 0 contains 512 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
ROUTER in Module 1/Slot 2: Revision 2: Active Ports [4,5,6] (enabled)
ROUTER in Module 1/Slot 4: Revision 2: Active Ports [4,5,6] (enabled)
Integral SCSI controller 2: Version QL1040B (rev. 2), differential
Integral SCSI controller 3: Version QL1040B (rev. 2), differential
Integral SCSI controller 4: Version QL1040B (rev. 2), differential
Integral SCSI controller 5: Version QL1040B (rev. 2), differential
Integral SCSI controller 0: Version QL1040B (rev. 2), single ended
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  CDROM: unit 6 on SCSI controller 0
Integral SCSI controller 1: Version QL1040B (rev. 2), single ended
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2
  PCI Adapter ID (vendor 0x1112, device 0x2200) PCI slot 1
Origin MSCSI board, module 1 slot 7: Revision 4
Origin BASEIO board, module 1 slot 1: Revision 4
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 3
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 2
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 0
  PCI Adapter ID (vendor 0x1077, device 0x1020) PCI slot 1
IOC3/IOC4 external interrupts: 1
HUB in Module 1/Slot 1: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 2: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 3: Revision 5 Speed 100.00 Mhz (enabled)
HUB in Module 1/Slot 4: Revision 5 Speed 100.00 Mhz (enabled)
IP27prom in Module 1/Slot n1: Revision 6.156
IP27prom in Module 1/Slot n2: Revision 6.156
IP27prom in Module 1/Slot n3: Revision 6.156
IP27prom in Module 1/Slot n4: Revision 6.156
IO6prom on Global Master Baseio in Module 1/Slot io1: Revision 6.156

henrycault · **Posted:** Sun Aug 30, 2009 11:58 am

Got some pics on its uber-technological wooden base. Will take more when i will mount it in a rack. It's also waiting for a MXE+IO6G hack, im still waiting after the IO6G. Oh and i should plug a KILL-A-WATT on it's outlet, im driving it from a standard 120V 15Amps socket, and the breaker never tripped yet. Im beggining to think that it would draw that humongous 2000 Watts only if it was totally full of XIO boards, and with a 100% cpu load. For now it looks more like a theoretical max current draw than a real thing, like if it had 8x500Mhz and maxed out ram and maxed out directory ram and so on.

Attachment:

O2k01.jpg [ 503.5 KiB | Viewed 109 times ]

Attachment:

O2k02.jpg [ 467.05 KiB | Viewed 109 times ]

^
|
Uber IBM Intellistation. lame x86 cpu.

Nekochan Net

Forum rules

CMN-A015 O2k system 8x250Mhz

Who is online