For those interested, an Onyx4 Ultimate Vision system config (Basically a Origin 350 chassis with a PCI USB card for keyboard & mouse, plus another 2U chassis with PCI ATI graphics cards installed). :
It's a 4 CPU system capable of driving 4 DVI outputs in 4U of space. I'm not sure about adding a 2nd nodeboard to the 2nd chassis at this point, not investigated.
Interestingly, the graphics brick shows up in l1cmd cfg as a "001v04" - not quite a V-brick, but almost.....
hinv -vm
Code:
Location: /hw/module/001c01/node
IP53_4CPU Board: barcode MZH384 part 030-1868-001 rev -C
Location: /hw/module/001c01/CGbrick/xtalk/10
2U_INT_53 Board: barcode MYE741 part 030-1809-003 rev -B
Location: /hw/module/001c01/IXbrick/xtalk/15
2U_INT_53 Board: barcode MYE976 part 030-1809-003 rev -B
Location: /hw/module/001c01/IXbrick/xtalk/15/pci-x/0/1/ioc4
IO9 Board: barcode MYS095 part 030-1771-005 rev -A
4 700 MHZ IP35 Processors
CPU: MIPS R16000 Processor Chip Revision: 2.1
FPU: MIPS R16010 Floating Point Chip Revision: 2.1
CPU 0 at Module 001c01/Slot 0/Slice A: 700 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz Tap 0xc
CPU 1 at Module 001c01/Slot 0/Slice B: 700 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz Tap 0xc
CPU 2 at Module 001c01/Slot 0/Slice C: 700 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz Tap 0xc
CPU 3 at Module 001c01/Slot 0/Slice D: 700 Mhz MIPS R16000 Processor Chip (enabled)
Processor revision: 2.1. Scache: Size 4 MB Speed 350 Mhz Tap 0xc
Main memory size: 2048 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 2048 MB (enabled)
Bank 0 contains 512 MB (Standard) DIMMS (enabled)
Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Bank 2 contains 512 MB (Standard) DIMMS (enabled)
Bank 3 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 2: Version IDE (ATA/ATAPI) IOC4
CDROM: unit 0 on SCSI controller 2
Integral SCSI controller 0: Version QL12160, low voltage differential
Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty3
IOC3/IOC4 serial port: tty4
IOC3/IOC4 serial port: tty5
IOC3/IOC4 serial port: tty6
Graphics board: SG2
Graphics board: SG2
Integral Gigabit Ethernet: tg0, module 001c01, PCI bus 1 slot 4
PCI Adapter ID (vendor 0x1002, device 0x4e47) PCI slot 1
PCI Adapter ID (vendor 0x1002, device 0x4e67) PCI slot 1
PCI Adapter ID (vendor 0x1002, device 0x4e47) PCI slot 1
PCI Adapter ID (vendor 0x1002, device 0x4e67) PCI slot 1
PCI Adapter ID (vendor 0x10a9, device 0x100a) PCI slot 1
PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 3
PCI Adapter ID (vendor 0x14e4, device 0x1645) PCI slot 4
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
PCI Adapter ID (vendor 0x1033, device 0x0035) PCI slot 1
PCI Adapter ID (vendor 0x1033, device 0x00e0) PCI slot 1
IOC4 firmware revision 79
IOC3/IOC4 external interrupts: 1
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
USB controller: type OHCI
USB Human Interface Device: device id 0 type mouse
USB controller: type OHCI
USB Human Interface Device: device id 0 type keyboard
l1cmd serial all
Code:
Data Location Value
------------------------------ ------------ --------
Local System Serial Number NVRAM M2004528
Reference System Serial Number Attached I/O M2004528
Local Brick Serial Number EEPROM MYE976
Reference Brick Serial Number NVRAM MYE976
EEPROM Product Name Serial Part Number Rev T/W
---------- -------------- ------------- -------------------- --- ------
INTERFACE 2U_INT_53 MYE976 030_1809_003 B 00
IO9 IO9 MYS095 030_1771_005 A 00
ODYSSEY no hardware detected
RISER 2U_RISER MZB272 030_1808_005 A 00
NODE IP53_4CPU MZH384 030_1868_001 C 00
SNOWBALL no hardware detected
PS 1 no hardware detected
PS 2 DPS-500EBE XPD0323001662 060-0178-003 S1
EEPROM JEDEC-SPD Info Part Number Rev Speed SGI
---------- ------------------------ ------------------ ---- ------ --------
DIMM 0 7F7FFE000000000012002554 CM2202B1 2 8.0 N/A
DIMM 2 7F7FFE0000000000120025FA CM2202B1 2 8.0 N/A
DIMM 4 no hardware detected
DIMM 6 no hardware detected
DIMM 1 7F7FFE000000000012002606 CM2202B1 2 8.0 N/A
DIMM 3 7F7FFE000000000012002600 CM2202B1 2 8.0 N/A
DIMM 5 no hardware detected
DIMM 7 no hardware detected
l1cmd env
Code:
Environmental monitoring is enabled and running.
Description State Warning Limits Fault Limits Current
-------------- ---------- ----------------- ----------------- -------
1.8V Enabled 10% 1.62/ 1.98 20% 1.44/ 2.16 1.78
12V Disabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.06
12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.06
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.32
12V IO Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.06
5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.02
3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.27
5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 5.02
3.3V Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.32
2.5V Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.51
5V Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 4.97
3.3V aux Disabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.27
XIO 12V bias Disabled 10% 10.80/ 13.20 20% 9.60/ 14.40 0.00
XIO 5V Disabled 10% 4.50/ 5.50 20% 4.00/ 6.00 0.00
XIO 2.5V Disabled 10% 2.25/ 2.75 20% 2.00/ 3.00 0.00
XIO 3.3V aux Disabled 10% 2.97/ 3.63 20% 2.64/ 3.96 0.00
NODE0 3.3V aux Enabled 10% 2.97/ 3.63 20% 2.64/ 3.96 3.25
NODE0 5V aux Enabled 10% 4.50/ 5.50 20% 4.00/ 6.00 4.99
NODE0 12V Enabled 10% 10.80/ 13.20 20% 9.60/ 14.40 12.00
NODE0 SRAM Enabled 10% 2.25/ 2.75 20% 2.00/ 3.00 2.48
NODE0 1.5V Enabled 10% 1.35/ 1.65 20% 1.20/ 1.80 1.49
NODE0 CPU Enabled 10% 1.13/ 1.38 20% 1.00/ 1.50 1.24
Description State Warning RPM Current RPM
-------------- ---------- ----------- -----------
FAN 0 EXHST 1 Enabled 2160 2311
FAN 1 EXHST 2 Enabled 2160 2327
FAN 2 PS Enabled 1575 2163
FAN 3 PCI 1 Enabled 2160 2556
FAN 4 PCI 2 Enabled 2160 2836
Advisory Critical Fault Current
Description State Temp Temp Temp Temp
-------------- ---------- --------- --------- --------- ---------
INTERFACE 0 Enabled 31C/ 87F 48C/118F 55C/131F 10C/ 50F
INTERFACE 1 Enabled 31C/ 87F 48C/118F 55C/131F 10C/ 50F
INTERFACE 2 Enabled 31C/ 87F 48C/118F 55C/131F 14C/ 57F
PCI RISER Enabled 31C/ 87F 48C/118F 55C/131F 13C/ 55F
ODYSSEY Disabled
NODE Enabled 31C/ 87F 48C/118F 55C/131F 11C/ 51F
BEDROCK Enabled 31C/ 87F 48C/118F 55C/131F 7C/ 44F
/usr/gfx/gfxinfo -v
Code:
Graphics board 0 is "SG2" graphics.
Managed (":0.0") 1280x1024
Memory Size: 128 MB
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 85.02Hz (1280x1024)
Video Format Flags: (none)
Sync Disabled
Using Gamma Map 0
Graphics board 1 is "SG2" graphics.
Managed (":0.1") 1280x1024
Memory Size: 128 MB
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 85.02Hz (1280x1024)
Video Format Flags: (none)
Sync Disabled
Using Gamma Map 0
Photos to follow in gallery. Feel free to ask any questions!
Login
Register
FAQ
Search
(single-CM)