O2 RM7000 400MHz DDS4

A place to post hardware inventories.
Forum rules
Please post your 'hinv' in the following format:

Topic: Kind of machine (O2, Octane, Tezro, Onyx2, etc.), CPU (R10k 250MHz, R12k 300MHz, R16k 1GHz, etc.), RAM, graphics option (Example: Tezro V12 4xR16K 700MHz 4GB)

Body: output of hinv -v (hinv -vm if possible) and /usr/gfx/gfxinfo.

Please wrap the output in BBCode "code" blocks to improve legibility.
User avatar
nekonoko
Site Admin
Site Admin
Posts: 8145
Joined: Thu Jan 23, 2003 1:31 am
Location: Pleasanton, California
Contact:

O2 RM7000 400MHz DDS4

Unread postby nekonoko » Wed Jan 07, 2004 5:47 pm

[Komugi:~] neko 50% hinv -v

Code: Select all

CPU: QED RM7000 Processor Chip Revision: 3.3
FPU: QED RM7000 Floating Point Coprocessor Revision: 2.0
1 400 MHZ IP32 Processor
Main memory size: 1024 Mbytes
Secondary unified instruction/data cache size: 256 Kbytes on Processor 0
Ternary unified instruction/data cache size: 1 Mbyte on Processor 0
Instruction cache size: 16 Kbytes
Data cache size: 16 Kbytes
FLASH PROM version 4.18
Integral SCSI controller 0: Version ADAPTEC 7880
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
  CDROM: unit 4 on SCSI controller 0
Integral SCSI controller 1: Version ADAPTEC 7880
  Tape drive: unit 6 on SCSI controller 1: DAT
Integral SCSI controller 2: Version IEEE1394 SBP2
On-board serial ports: tty1
On-board serial ports: tty2
On-board EPP/ECP parallel port
CRM graphics installed
Integral Ethernet: ec0, version 1
Iris Audio Processor: version A3 revision 0
  PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 1
  PCI Adapter ID (vendor 0x9004, device 0x8078) PCI slot 2
  PCI Adapter ID (vendor 0x104c, device 0x8024) PCI slot 3
Video: MVP unit 0 version 1.4
AV: AV1 Card version 1, O2Cam type 1 version 0 connected.
Vice: TRE
1600SW Flat Panel adapter board and display.
DMediaPro DM10 FW option: unit 0, revision 1.1.0


[Komugi:~] neko 51% /usr/gfx/gfxinfo -v

Code: Select all

 
Graphics board 0 is "CRM" graphics.
        Managed (":0.0") 1600x1024
        32 bitplanes
        board revision 2, CRM revision C, GBE revision B
        Timing table flags:
         Monitor 0 type: Unknown
        Channel 0:
         Origin = (0,0)
         Video Output: 1600 pixels, 1024 lines, 60.00Hz (1600x1024_60p)
         Video Format Flags:  (none)
         Sync Disabled
         Using Gamma Map 0


[Komugi:~] neko 1# scsicontrol -I /dev/scsi/sc1d6l0

Code: Select all

/dev/scsi/sc1d6l0:  Tape          SONY    SDT-10000       0110
ANSI vers 2, ISO ver: 0, ECMA ver: 0; supports:  16bit synch
Device is  ready
Last edited by nekonoko on Thu Feb 17, 2005 11:40 pm, edited 6 times in total.
Twitter: @neko_no_ko
IRIX Release 4.0.5 IP12 Version 06151813 System V
Copyright 1987-1992 Silicon Graphics, Inc.
All Rights Reserved.

User avatar
Scott Tarr
Posts: 120
Joined: Sat Jul 26, 2003 1:08 pm
Location: Detroit Metro area

Unread postby Scott Tarr » Wed Mar 10, 2004 9:18 pm

I've noticed a few of the O2's here have 16:10 video outputs. Am I missing something somewhere to adjust my O2's output to fit my 16:10 monitor?

User avatar
nekonoko
Site Admin
Site Admin
Posts: 8145
Joined: Thu Jan 23, 2003 1:31 am
Location: Pleasanton, California
Contact:

Unread postby nekonoko » Wed Mar 10, 2004 9:34 pm

I don't know - I have an SGI 1600sw flat panel on mine which is 1600x1024 hooked to digital output. I've never used an O2 on anything else.
Twitter: @neko_no_ko
IRIX Release 4.0.5 IP12 Version 06151813 System V
Copyright 1987-1992 Silicon Graphics, Inc.
All Rights Reserved.

User avatar
Scott Tarr
Posts: 120
Joined: Sat Jul 26, 2003 1:08 pm
Location: Detroit Metro area

Unread postby Scott Tarr » Thu Mar 11, 2004 8:34 pm

Interesting. I have the 1600sw option but do not have a 1600sw to try that with.

I would think that if it's a solution on the 1600sw then it should just do it natively according to build of OS (I assume).

I have a 24" sgi monitor but no 16:10 love when using the O2.

User avatar
colin
Posts: 453
Joined: Sat Feb 07, 2004 5:43 pm
Location: Lubbock, Texas
Contact:

Unread postby colin » Sat May 08, 2004 10:32 pm

Scott Tarr wrote:I would think that if it's a solution on the 1600sw then it should just do it natively according to build of OS (I assume).

I have a 24" sgi monitor but no 16:10 love when using the O2.

O2 can only do 1600x1024 resolution (16:10 aspect ratio) via the digital 1600sw output. It cannot do that resolution via the analog HD15 output due to hardware limitations.

User avatar
GeneratriX
Posts: 4250
Joined: Tue Oct 21, 2003 2:07 am
Location: Rosario / Santa Fe / República Argentina

Unread postby GeneratriX » Sat May 08, 2004 10:59 pm

colin wrote:
Scott Tarr wrote:I would think that if it's a solution on the 1600sw then it should just do it natively according to build of OS (I assume).

I have a 24" sgi monitor but no 16:10 love when using the O2.

O2 can only do 1600x1024 resolution (16:10 aspect ratio) via the digital 1600sw output. It cannot do that resolution via the analog HD15 output due to hardware limitations.


O2 can do 1600x1024, but it gives a little error of visual/geometry memory area, copying the upper/left corner (rectangle shape area) on the lower/right corner.

An effect interesting, if you learn to leave with it! ...with a little short time, you can love it! :lol:

But seriously; I've touched my own vof templates, to reduce at minimun. But simply u can't remove completely the thingy of the lower/right corner... :(


Return to “SGI: hinv”

Who is online

Users browsing this forum: No registered users and 1 guest