Cube logo obj model

3D/2D CGI and the tools used in their creation (Maya, Photoshop, Blender, GIMP, etc.).
Forum rules
Any posts concerning pirated software or offering to buy/sell/trade commercial software are subject to removal.
Post Reply
DaJuice
Posts: 159
Joined: Fri May 09, 2003 11:51 pm
Location: Arizona

Cube logo obj model

Unread postby DaJuice » Sat Dec 26, 2015 9:44 pm

I know there are others but here's my attempt at it.

logo_01.jpg
logo_01.jpg (40.05 KiB) Viewed 897 times

logo_02.jpg
logo_02.jpg (169.89 KiB) Viewed 897 times
Attachments
sgi_cube_logo.obj.gz
(85.79 KiB) Downloaded 68 times
Top
User avatar
dexter1
Moderator
Moderator
Posts: 2780
Joined: Thu Feb 20, 2003 6:57 am
Location: Zoetermeer, The Netherlands

Re: Cube logo obj model

Unread postby dexter1 » Sun Dec 27, 2015 12:31 am

Good work DaJuice! i like the way you did the joints, smoothing out the inner section.
:Crimson: :PI: :Indigo: :O2: :Indy: :Indigo2: :Indigo2IMP:
Top
User avatar
foetz
Moderator
Moderator
Posts: 6704
Joined: Mon Apr 14, 2003 4:34 am
Contact:
Contact foetz

Re: Cube logo obj model

Unread postby foetz » Sun Dec 27, 2015 3:52 am

nice. maybe you could add a few words about how you did it? and what you used and so on ...
Top
User avatar
vishnu
Donor
Donor
Posts: 3361
Joined: Sun Mar 18, 2007 3:25 pm
Location: Minneapolis, Minnesota USA

Re: Cube logo obj model

Unread postby vishnu » Sun Dec 27, 2015 8:30 am

Nice! :D And, not to belabor the point made by foetz but it'd be nice to know what you used to make it... :roll:
Project:
Temporarily lost at sea...
Plan:
World domination! Or something...
:Tezro: :Octane2:
Top
DaJuice
Posts: 159
Joined: Fri May 09, 2003 11:51 pm
Location: Arizona

Re: Cube logo obj model

Unread postby DaJuice » Sun Dec 27, 2015 12:02 pm

Thanks guys, it was made in Houdini 15 on PC. If there is interest I will try to get Houdini 6.5 installed on the Octane2 and see if the same steps can be applied. It's been a while since I used that version so I'm not sure which modeling tools are missing. Either way, it shouldn't bee too bad.
Top
User avatar
foetz
Moderator
Moderator
Posts: 6704
Joined: Mon Apr 14, 2003 4:34 am
Contact:
Contact foetz

Re: Cube logo obj model

Unread postby foetz » Sun Dec 27, 2015 12:48 pm

thanks but no thanks :P everything after houdini5 on irix didn't run well at all.
that aside the joints dexter1 mentioned are too harsh. you'll see that if you're using a darker shader, they stand out too much like they wouldn't be part of the object.

maybe we can use this thread as a call to arms so to say and see if more members contribute their version of the logo. would be great having some kind of collection here.
Top
User avatar
duck
Donor
Donor
Posts: 760
Joined: Mon Oct 27, 2003 5:22 pm
Location: Jakobstad, Finland
Contact:
Contact duck

Re: Cube logo obj model

Unread postby duck » Sun Dec 27, 2015 2:03 pm

Being the lazy guy I am I just extruded a nurbs tube. Your curves are pretty darn nice though, props.

snap.png
Attachments
sgi_cube.ma.gz
Lazy NURBS SGI cube
(6.66 KiB) Downloaded 49 times

Code: Select all

___(o)=
\____)
Top
DaJuice
Posts: 159
Joined: Fri May 09, 2003 11:51 pm
Location: Arizona

Re: Cube logo obj model

Unread postby DaJuice » Sun Dec 27, 2015 2:50 pm

foetz wrote:maybe we can use this thread as a call to arms so to say and see if more members contribute their version of the logo. would be great having some kind of collection here.

Cool, I like that idea.

duck wrote:Being the lazy guy I am I just extruded a nurbs tube. Your curves are pretty darn nice though, props.

snap.png

Nice, thank you for sharing. :D
Top
Post Reply

Return to “SGI: Computer Graphics”

Who is online

Users browsing this forum: No registered users and 1 guest